Current Quarantine Protocol

OMG, so I just did a bit of digging on this and I think the reason the Hanna meter shows a reading with ~0.50ppm higher is because the copper is in the water and the optical sensor picks that up... Hmmm.... this changes everything.
Test ammonia 48 hours later. Some say they get good readings even after only 24 hours. Yes, as Jay stated, copper will give you at least .5ppm reading.

Did you cycle the QT tanks for 23-48 before putting the fish in the tank? Some bacteria brands state to cycle for 24-48 hours before fish go in.
 
Correct, the theory is that the Seachem disks do not register phantom ammonia. However, IMO, these disks have a pretty high failure rate, and I don’t rely on them.

I wouldn’t worry about ammonia in a copper treated tank unless it is reading higher day to day and approaching 1 ppm (so 0.5 ppm of actual ammonia).

There is also a pH component to ammonia toxicity - the higher the pH, the more of the total ammonia will be in its toxic form.
Thank you for your help Jay, this helps a lot!

-Paul
 
Tomorrow I am picking up an Australian stripey from a local fish store and adding it to my QT tank. Normally I start with just saltwater, give the fish a few days for observation, then use Copper Power to get the copper level up to 2.25ppm. However, this fish store runs copper in their fish only tanks. I took a water sample home today and tested it with my Hanna copper checker and it's showing 2ppm. Should I raise my QT up to 2ppm copper before adding the fish?
 
Tomorrow I am picking up an Australian stripey from a local fish store and adding it to my QT tank. Normally I start with just saltwater, give the fish a few days for observation, then use Copper Power to get the copper level up to 2.25ppm. However, this fish store runs copper in their fish only tanks. I took a water sample home today and tested it with my Hanna copper checker and it's showing 2ppm. Should I raise my QT up to 2ppm copper before adding the fish?
I would. Or just start at 2.25.
 
Tomorrow I am picking up an Australian stripey from a local fish store and adding it to my QT tank. Normally I start with just saltwater, give the fish a few days for observation, then use Copper Power to get the copper level up to 2.25ppm. However, this fish store runs copper in their fish only tanks. I took a water sample home today and tested it with my Hanna copper checker and it's showing 2ppm. Should I raise my QT up to 2ppm copper before adding the fish?

These are tough fish. No issues at all moving it right in to 2.25

Just the standard caution that many dealers run lower salinity, so be sure to match their salinity (assuming no other fish in the qt ATM)
 

TOP 10 Trending Threads

WHAT KIND OF REEFING DEAL ARE YOU HOPING TO PICK UP THIS BLACK FRIDAY?

  • A whole new aquarium or complete system

    Votes: 2 11.1%
  • Lighting, pumps, or other major equipment

    Votes: 2 11.1%
  • Controllers, testing, dosing, or automation gear

    Votes: 2 11.1%
  • Dry goods and restocks, like salt, media, or food

    Votes: 2 11.1%
  • Corals! Must...Have...CORALS!!!

    Votes: 5 27.8%
  • Fish or other livestock

    Votes: 0 0.0%
  • Rock, sand, or other aquascaping supplies

    Votes: 1 5.6%
  • I’m browsing, but don’t have a specific target

    Votes: 2 11.1%
  • I’m not shopping for reef deals this year

    Votes: 1 5.6%
  • Other (Post in the comments)

    Votes: 1 5.6%
Back
Top
Home
Post thread…
Market
What's new