DSA 185 build (barts old tank)

[Dowtish]

Since you already have it in place just fill it up with freshwater and a couple of gallons of vinegar. Let it run for 24 hours, and drain it, and clean it, rinse it, and fill it up saltwater. easier said than done. Have fun with that

 

[gmoney243]

So do you think I should let the tank run for a day or so with fresh water

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

I used 2g when I cleaned my tank out. 6 is to much. As stated let it run for cpl days then it just wipes clean.

Sent from my Vortex using Tapatalk 2

 

[orthokardia]

I had that same size from DSA. You should love it!

Alex,
Your tank is still in the club. There is a build thread on hear somewhere. The 40b is also packed with coral. I hope HI is treating you well.
-bart

 

[orthokardia]

Looking good Luis!! This is just as exciting as when I was setting it and a lot less work I wonder if this is what it feels like to be a grandparent??

 

[iiluisii]

Looking good Luis!! This is just as exciting as when I was setting it and a lot less work I wonder if this is what it feels like to be a grandparent??

Lol

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[iiluisii]

Return done.

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[schooleyosis]

Alright! progress...

 

[iiluisii]

Yea but im running into problems with my return pump being to powefull for my overflow I think

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[schooleyosis]

Throttle it back with a ball valve...

 

[iiluisii]

I did but it does not work. Do you guys summerge you drain pipes under water

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[angrycubano]

When I was setting mine up my return section was emptying too quickly so I opened up my drain section a bit and dialed back the return. It was almost impossible to find the happy medium but eventually it leveled itself.

 

[schooleyosis]

My drain is underwater. Single 1.5" drain with a mag 18 running wide open on a 1" return.

 

[iiluisii]

My drain is underwater. Single 1.5" drain with a mag 18 running wide open on a 1" return.

I have two one inch drains dumping into my sump and they are sumerged and I have an iwaki md55 which is 1100 GPH and when I turn it on the water level on the over flow goes almost on top of the dorsal and were the water is dumping to the sump is pushing the water so hard that it splashes about 2 inches high it look like a hot top with the water jets going full blast

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[Dowtish]

I did but it does not work. Do you guys summerge you drain pipes under water

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

What do you mean it does not work?

 

[iiluisii]

What do you mean it does not work?

I had it a little less than half throttle and it barely change anything

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[gmoney243]

Pics bro. Else we can't help figure ur drain out. Drains should easily handle 1100gph. Are u using durso pipes?

Sent from my Vortex using Tapatalk 2

 

[iiluisii]

Here is a video. Me and mike talk about it for a bit. It might be that my dorsal pipes are 1 inch and maybe need to do a bigger pipe plus the drain pipes going to my sump they are going to far down in the water so im gonna cut them. Also I migh change all the drain pipping going to the sump to 1.5
https://www.youtube.com/watch?v=YgV4qojBsgE&feature=youtube_gdata_player

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

 

[pickupman66]

a pair of 1" dursa pipes should be able to handle the flow just fine. I ran the same pump on a closed loop that was 1" and it performed perfectly. I can drain my 180 with a single 1 1/2" pipe but I use two for redundancy. sounds like your durso's are setup properly or have some sort of air lock preventing full flow. Personally, I dont like my drain pipe under water. it can cause a backup. hopefully you didnt glue the tops of your Durso's together. if not, remove teh cap on the top and see how they are performing.