Electronic Carbon Doser problem need help...

  • Thread starter Thread starter Scubabum
  • Start date Start date
  • Tagged users Tagged users None

Scubabum

Well-Known Member
View Badges
Joined
Mar 3, 2015
Messages
745
Reaction score
1,039
Location
United States
What state or country do you live in
California
Rating - 100%
1   0   0
Calcium reactor users need help.
67784891_10218195204248089_4944733098412605440_o.jpg
I'm fairly new to Calcium Reactors. Tonight I heard a loud noise and found the carbon doser regulator venting from the area circled. Super cold around the vent. Calcium reactor setup has been running 8 months without issue. Any ideas???
 
Last edited:
Looks like a pressure release valve, it was cold bc of the high pressure venting to low pressure making it cold. It's like a safety feature for over pressurization. But could also be a failing valve. I'd reset it and see if it happens again. If it does. I'd look into replacing the valve.
Did you do anything the trip the valve? Meaning change tanks over pressurize the outlet somehow? Just a though... but I'd lean towards the vale
 
Looks like a pressure release valve, it was cold bc of the high pressure venting to low pressure making it cold. It's like a safety feature for over pressurization. But could also be a failing valve. I'd reset it and see if it happens again. If it does. I'd look into replacing the valve.
Did you do anything the trip the valve? Meaning change tanks over pressurize the outlet somehow? Just a though... but I'd lean towards the vale
Thank you. Looking for my manual on how to reset it. I didn't do anything, haven't touched it in months. Just heard the noise and discovered it venting.
 
It is a pressure safety relief stem. It is supposed to trigger if the low pressure side of the unit exceeds 40 psi. Says in the instructions that ‘you should never touch it’. What did you have the low pressure gauge set to? I shoot for 10 psi on mine. More than enough to offset any CaRx internal pressure. You are also supposed to make sure the pressure knob is unthreaded all the way before opening up a new CO2 cylinder. Relief valve is cold because cylinder contans liquid and in the process of expanding to a gas heat is consumed, thus the valve is cold.
 
It is a pressure safety relief stem. It is supposed to trigger if the low pressure side of the unit exceeds 40 psi. Says in the instructions that ‘you should never touch it’. What did you have the low pressure gauge set to? I shoot for 10 psi on mine. More than enough to offset any CaRx internal pressure. You are also supposed to make sure the pressure knob is unthreaded all the way before opening up a new CO2 cylinder. Relief valve is cold because cylinder contans liquid and in the process of expanding to a gas heat is consumed, thus the valve is cold.
It was set to 5.5-6 psi. Been running flawless for 8 months. The tank pressure gauge was reading 700 PSI this morning prior to the blow off but I noticed the bottle felt super light. This is my first bottle of Co2 and when I started it up I did open the valve all the way prior to turning on the gas. Not sure if a low bottle would cause this. I'm new to using a Calcium Reactor.
 
As a CO2 cylinder gets close to empty, and the liquid is gone, pressure usually drops pretty fast. Hard to see that this would cause an over pressure incident. Might be worth swapping out the cylinder to see if that cures the problem. Might need to contact aquarium plants and ask.
 
UPDATE..... I contacted Aquarium Plants and they told me to try and lift and release the pin on the pressure relief valve while gas was on. While performing this test I discovered the gas was coming from the connection to the tank and was not the pressure relief valve. Simply replaced the perma seal and all functioning normal again. Thanks everyone who responded.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new