Help ! Power head blowing sand everywhere!

  • Thread starter Thread starter BigFeesh
  • Start date Start date
  • Tagged users Tagged users None

BigFeesh

Well-Known Member
View Badges
Joined
Dec 27, 2010
Messages
810
Reaction score
2
Location
Chicago area
Rating - 0%
0   0   0
I have a 750 gph power head in my 29 bc with like 22-25lbs of LR and the tank has been going for three weeks. no matter how I position it the current hits the glass and circle around and pushes sand until the bottom of the tank shows. It's making me mad because I don't want to keep moving my sand around . Any suggestions ?
 
Nah, that pump should be fine in there. Try placing it on the back wall, only a few inches above the sand and aim it towards the water surface. Should also help to create a bit of an undertow.
 
seems like that close to the sand it would possible pick the sand up and pull it into the current maker, atleast if it is lit and fine sand...
 
Trade it for 2 smaller powerheads .... will give you more diverse flow with less force concentrated on one spot so less sand will be lifted... unless you are using powder thin sand!
 
Trade it for 2 smaller powerheads .... will give you more diverse flow with less force concentrated on one spot so less sand will be lifted... unless you are using powder thin sand!

using aragonite . But awesome idea thanks!!!!
+++++1
 
couple things you can do...

  1. keep it near the top blowing up for the first little bit - your sand needs a couple months to get clumpy once its all live (i assume you are using some new stuff)
  2. get a larger grain sand and put a layer on top of your current sand bed. it will be harder to kick up
  3. have it blow right at the rocks that way the slower deflected flow does most of the circulation within your tank.
 
It has been blowing toward top and tried at rocks . I'm just going to give it to my bro for his 65 gal cichlid tank and il get a couple 250s. Thank you eeerbody.
 
There are many different sizes or aragonite sand. I had the same problem in my tank and ended up replacing the sand. I went with caribsea seaflor special grade reef sand, its a courser sand. As I got into sps I found this was the best solution. That or go BB but I like the look of sand.
 
bare bottom: best solution ever

True..!! but not as aesthetically pleasing for all of us!!!

What about two 250gph powerheads

Probably will work... depends on what corals you plan on keeping.... the best I believe will be to upgrade to an mp10... these pumps are awesomee!!! and you can play with the setting to see what suits you best... plus also will not look to bulky in your tank!!
 
There are many different sizes or aragonite sand. I had the same problem in my tank and ended up replacing the sand. I went with caribsea seaflor special grade reef sand, its a courser sand. As I got into sps I found this was the best solution. That or go BB but I like the look of sand.
Did you have to take the fish out to switch the sand?
 
I certainly hope he’s got it all settled by now lol! ;Smuggrin
My sand blows around my tank, it leaves a bare bottom, area, cause of the wave pump, its a lil low in my tank, cause I don’t want any dead spots, Do caribsea seaflor special grade reef sand work? I want to switch the sand so bad it irks me everytime I look at my tank, no matter how many times I move sand where it’s bare bottom at, it moves again
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new