ICP test and high Sulfer?

  • Thread starter Thread starter Greg Depo
  • Start date Start date
  • Tagged users Tagged users None

Greg Depo

Active Member
View Badges
Joined
Jan 27, 2019
Messages
294
Reaction score
143
Location
Indianapolis
What state or country do you live in
Indiana
Rating - 0%
0   0   0
So I today I got my icp results back. I noticed a few parameters are off. The one of greatest concern would be sulfur was elevated. The comments on the test said check your salt mix. I switched to tropic marin about a month ago. Anyone else notice this using TM and then obviously is this something that can hinder coral growth or something I should be concerned about?
 
Well, obviously the level would be worth knowing. lol

In general, sulfate is the third highest weight concentration in in seawater, at about 2700 ppm sulfate, and variations in it are not likely a big deal. Salt mixes do vary and unless you have been dosing a lot of Epsom salt for magnesium, then the salt mix is the source.
 
Well, obviously the level would be worth knowing. lol

In general, sulfate is the third highest weight concentration in in seawater, at about 2700 ppm sulfate, and variations in it are not likely a big deal. Salt mixes do vary and unless you have been dosing a lot of Epsom salt for magnesium, then the salt mix is the source.

Ha Probably a good idea huh!

Sulfur S
Value: 996.9
Result:
high.png

Calculated reference value: 815.0

Also my mag doesn't appear elevated
Magnesium Mg
Value: 1324
Result:
check.png

Calculated reference value: 1165

Only other value of note that was elevated was iodine which was substantially higher.

Iodine I
Value:329.7
Result:
high.png

Calculated reference value: 57.58
 
Last edited:
Their reference value is way too low, unless it is being calculated based on your salinity being low.


35 ppt seawater contains 2700 ppm sulfate, which includes 900 ppm sulfur.

What is your salinity?

In any case, i would not worry much about sulfate if you are not dosing it.
 
Their reference value is way too low, unless it is being calculated based on your salinity being low.


35 ppt seawater contains 2700 ppm sulfate, which includes 900 ppm sulfur.

What is your salinity?

In any case, i would not worry much about sulfate if you are not dosing it.

The salinity was lower than I anticipated... Maybe I don't fully understand salinity compared to gravity but my refractometer and old school swing arm device shows .026. Not sure if it means anything towards sulfur but I am dosing Sodium Bicarbonate from BRS.

Salinity (NaCl) NaCl
Value:31.00
Result:
low_med.png

Calculated reference value: 35.00

I'd like to bring that up to the 35ppt so I ordered some calibration fluid to make sure my refractometer is correct.
 
Ok, that low salinity is why they say sulfate should be low.

The sodium bicarbonate is not altering sulfate.

Calibration fluid sounds like a good plan.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new