Old mp 40

Noob_reefer

Active Member
View Badges
Joined
May 12, 2019
Messages
190
Reaction score
123
What state or country do you live in
Florida
Rating - 0%
0   0   0
I bought a used mp40 wes over the weekend. The dryside is sliding down and not sticking to the wet side straight anymore. Any idea on how or where I can the dryside without replacing the controller if possible.
 
Have you got the sticky bad that fits under the dryside, if not you need to get one otherwise that might be why its not sticking.

They also as new come with tie raps/stickers to stop them falling off completely.
 
Have you got the sticky bad that fits under the dryside, if not you need to get one otherwise that might be why its not sticking.

They also as new come with tie raps/stickers to stop them falling off completely.
I didn't get any of that I figured the magnets would be enough lol. It was pretty heavy tbh
 
Most who do not follow the instructions of using the sticky pads and tie wraps find their dry side busted on the floor, sooner or later.
So you would reccomend getting the sticky pads and tie wraps
 
Sticky pads, not the dry side
Which sticky pads would you recommend, sorry if I'm being annoying or seem stupid I have never had an ecotech power head before and I bought it used so it didn't come with that
 
Which sticky pads would you recommend, sorry if I'm being annoying or seem stupid I have never had an ecotech power head before and I bought it used so it didn't come with that
If you google - "self adhesive cable tie mount" you should get what you need. Small stcky block that allows a cable tie through it. Tie the wire for the Vortech above the pump so it can no longer move anywhere.
 
How old of an MP40.....older ones you had to adjust for glass thickness by pulling off the cover on the dry side and aligning to the glass thickness.

0-F3NseGPRZkNCR1Ny2zYsCzH8JiUQ0e_iR3KOP5wJUUAKfDsg95VII6zzDikd1HVFrxHIgiDYprkNSK97X9VAi4Qji5CTFkJ3pqB6ToypfrYkpG6Z-xQck-bdHHIOh2PYZOwBqbEp3DJkJV57Ggkjt9H76mVnFo_gnO1Cgp5O58Ea6D6uHpQKPxE9jP9btTURgvzDxgpeTh9Ht4j4_nO_NFkY5lkdwdm2LaK2D87qyRDynVCWbrmzjlIIkQp7p6chdsAosGfjrrR6Pm9CTA6Xfht38rX-hGqGOJp5brjAlNesluqpga_vBOeolDfiKt5xAO40IRvixIOAJzKpKJK1v3LgBS6b7c7VvwMpIO2BXIHr2ZDYjtr6CtpfgyqyGUsV-Qz1HNY7_Oty1L0pVlS4qRTHKJxnlIcN9u4s15rVvxQSKelITwPaJKdTL8Pimla0f27Bs3Oz239woliCluMfAKREkbM-1DNpA3cO_pTpYSHlHaGMAGQIHLA_hBdPyH8xmbh2FZmPN2GQwSXqgP-sSy9sA3FFT3Qd3MEyFMrShEgjOoX7cmvQgfVAvWdUI_XnbaSBiS8lxydutsksOrMd3TPzNaJp_8yz86Ba3QSKWV6EmJT_eAqiEkOoiP2d946R0XM8kql3SuuiGSC0xf5FcT5uJVNe9cAmC1o6yFnGGo9RDEvSEznno=w693-h923-no
 
Last edited:
These …..

s-l300.png

I buy them at home depot, next to the zipties.
 
How old of an MP40.....older ones you had to adjust for glass thickness by pulling off the cover on the dry side and aligning to the glass thickness.

0-F3NseGPRZkNCR1Ny2zYsCzH8JiUQ0e_iR3KOP5wJUUAKfDsg95VII6zzDikd1HVFrxHIgiDYprkNSK97X9VAi4Qji5CTFkJ3pqB6ToypfrYkpG6Z-xQck-bdHHIOh2PYZOwBqbEp3DJkJV57Ggkjt9H76mVnFo_gnO1Cgp5O58Ea6D6uHpQKPxE9jP9btTURgvzDxgpeTh9Ht4j4_nO_NFkY5lkdwdm2LaK2D87qyRDynVCWbrmzjlIIkQp7p6chdsAosGfjrrR6Pm9CTA6Xfht38rX-hGqGOJp5brjAlNesluqpga_vBOeolDfiKt5xAO40IRvixIOAJzKpKJK1v3LgBS6b7c7VvwMpIO2BXIHr2ZDYjtr6CtpfgyqyGUsV-Qz1HNY7_Oty1L0pVlS4qRTHKJxnlIcN9u4s15rVvxQSKelITwPaJKdTL8Pimla0f27Bs3Oz239woliCluMfAKREkbM-1DNpA3cO_pTpYSHlHaGMAGQIHLA_hBdPyH8xmbh2FZmPN2GQwSXqgP-sSy9sA3FFT3Qd3MEyFMrShEgjOoX7cmvQgfVAvWdUI_XnbaSBiS8lxydutsksOrMd3TPzNaJp_8yz86Ba3QSKWV6EmJT_eAqiEkOoiP2d946R0XM8kql3SuuiGSC0xf5FcT5uJVNe9cAmC1o6yFnGGo9RDEvSEznno=w693-h923-no
My mp40 has that sticker... should I remove it or is there something to it
 
My mp40 has that sticker... should I remove it or is there something to it
Measure your glass thickness or ask manufacturer. Put the cap off and align with your glass thickness. Right now the picture is set for 3/8" thickness. Likely why your MP40 was sliding down..
 
As @NeonRabbit221B said, you need to first measure the thickness of the glass/acrylic and then set the dryside to that thickness. You do this by pulling off the "labeled" piece and align the thickness on the label to the wire going into the dryside. Note that at times I've had difficulty pulling off this base piece....and also aligning the three pins to put it back on.

rk20APdd88law1Rk8bMwivmpGW9aeJ0qY-pBGwHQWflg-V_eqvduLpkxZkA2Frh4uupFp7vGNG5Wlmi9666w7voiqF9pGmifFR8ijK9fN1UunS7Cg_Y8fpDGFZEBpwhJDrX9vXXrbZ7lVEWkKucajDE5RdfJwj1q6qPD5-0WWitSajqeE46IUjEmWeRv4m5sheFyGC9XrpIGjij-wjuRsotUmJFA865RkvYs_4FdN_WIxgIdYCyXAaV3y6AwUZLSrmQwZDi833PgHi-mXQCcImeVBd9a6OTwSg0h9V2lug-ea1cgLG6Ye02xrCLQZwwSlhGQIAnD6lRpb8vNWVj0J_lHQf1Jr-AK4bu8KiUp8gvujc2DfQJXLfoBx8_BeUGnf8pvi_-vNMdVToeF_G0A3hWaBV00cK5caSnU7YAciYcqN1v2KyoL23-W37RcMwIjSp0t3QYs522Q8aU2lptJShBfhzlATqdPfC4Q_rV6DhpUXM8mhB-w6szfUNiZci5uzmqNAzzNR_yeHZvR0xer0AEx_JLWDciBtZdB9WA-PIn4Xr0_9lW5U9BE4fTISIzKNZdPthFEKTO1iaZ2fNf99ZVtAuoMtg7TCJvMUea3qYBTRoOXL9izooBzSJIP4KVgNwVOFuRNFftX6-BOTyjXswzpO6ztcpgv-3fx4bwTcoitr-RETl7zkw4=w693-h923-no
 
As @NeonRabbit221B said, you need to first measure the thickness of the glass/acrylic and then set the dryside to that thickness. You do this by pulling off the "labeled" piece and align the thickness on the label to the wire going into the dryside. Note that at times I've had difficulty pulling off this base piece....and also aligning the three pins to put it back on.

rk20APdd88law1Rk8bMwivmpGW9aeJ0qY-pBGwHQWflg-V_eqvduLpkxZkA2Frh4uupFp7vGNG5Wlmi9666w7voiqF9pGmifFR8ijK9fN1UunS7Cg_Y8fpDGFZEBpwhJDrX9vXXrbZ7lVEWkKucajDE5RdfJwj1q6qPD5-0WWitSajqeE46IUjEmWeRv4m5sheFyGC9XrpIGjij-wjuRsotUmJFA865RkvYs_4FdN_WIxgIdYCyXAaV3y6AwUZLSrmQwZDi833PgHi-mXQCcImeVBd9a6OTwSg0h9V2lug-ea1cgLG6Ye02xrCLQZwwSlhGQIAnD6lRpb8vNWVj0J_lHQf1Jr-AK4bu8KiUp8gvujc2DfQJXLfoBx8_BeUGnf8pvi_-vNMdVToeF_G0A3hWaBV00cK5caSnU7YAciYcqN1v2KyoL23-W37RcMwIjSp0t3QYs522Q8aU2lptJShBfhzlATqdPfC4Q_rV6DhpUXM8mhB-w6szfUNiZci5uzmqNAzzNR_yeHZvR0xer0AEx_JLWDciBtZdB9WA-PIn4Xr0_9lW5U9BE4fTISIzKNZdPthFEKTO1iaZ2fNf99ZVtAuoMtg7TCJvMUea3qYBTRoOXL9izooBzSJIP4KVgNwVOFuRNFftX6-BOTyjXswzpO6ztcpgv-3fx4bwTcoitr-RETl7zkw4=w693-h923-no
Omg! Thank you I didn't know about this lol
 
Yeah, dumped my last old dryside last year. Getting the spacer cap on and off was a major pain. Seems clear why the whole thing was redesigned.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new