PVC and Eels

[Goodair]

How do you all set up tunnles with pvc for eels?
-Burried under the substrate/above
-How long to span
-do you siphon the inside from time to time
-anything else to consider?

 

[Eagle_Steve]

How do you all set up tunnles with pvc for eels?
-Burried under the substrate/above
-How long to span
-do you siphon the inside from time to time
-anything else to consider?

When we built our aggressive tank at the old house, we put pipes all over the place for the eel. The pipes sit under the rocks and in the rocks. We did not create any 3 or 4 way joints though. Always worried me with keeping them clean. To clean, we just blew out with an mj1200. The pipes all had 45s for turns and 45s at the entryway/exit way and we’re slightly above the sand. The eel loved it and would go from one to the other when cruising around.

 

[DJ H]

I had eels in my reef no pvc but a ton of rock . Make some rock tunnels

 

[Goodair]

I have some caves, was looking at adding pvc to have longer stretches of cave networks for the eel to feel comfortable with.

 

[lion king]

What type of eel(s), I've never found it necessary in most cases. I do have pvc for my ribbon eel but mainly because I had to move him to a mature tank that wasn't built for him. Building natural caves and pathways along the back way is much better in my opinion. If you are decided on pvc, built under the substrate and rocks built on top is much nicer. Depending on the type of eel you could be using a large diameter pvc which will take alot to cover. If the eel actually does use the pvc, his travels will clean it out so there is nothing for you to do. Occasionally if you don't provide a large enough, or too large pvc, or for whatever reason; some won't use it, then there's a problem with dietritus.

 

[Goodair]

Mostly research, it would be a snowflake eels more likely since they are smaller. Maybe a skeltor moray (something in the Echidna family) but more likely the snowflake. What would be a good diameter for the pvc? Some of the caves already get occupied so looking to add more options to avoid territory aggression. There is already so much rock in the tank, not too much more floor space to occupy.

 

[lion king]

For pvc diameter I would do 2". How do you plan to run it, it's somewhat tricky in a tank already scaped. While I like 3 openings for my eel, my ribbon lives in a simple 2 opening, one in the front of the tank, one in the back side of the tank, I can observe him from each opening. You can use 45 degree connectors to maneuver through rocks and a 45 at the openings to lend to a more natural look. I am not happy with the pvc for my ribbon because I didn't plan on putting him in this tank and there wasn't much room for me to maneuver.

 

[Goodair]

First thought was to snake it between the rocks and overhangs. Have 1 opening on the right side of the tank, the other in the front right. If possible, I can use a T or Y fitting and have 2 openings in the front both left and right side. Then try to bury it in the substrate and use black/gray fittings as openings, so its not as much as an eye sore.

 

[Goodair]

Circles would be openings, 2 in front, 1 in back right where I can still see inside it.

 

[CMO]

I have a pvc tunnel under my substrate with rock on top. Works very well and the eel loves it. No need to clean it really as your clean up crew, pods etc with take care of that for you. Size the Pvc to a tight fit for full grown size both girth and length. If you get the eel when it's smaller it may not use the Pvc tunnel until it grows into it as they like tight spaces. The Pvc tunnel is nice because you can position an entrance towards the front of the tank where you'll generally be able to see it hanging out (vs it hiding somewhere in the rocks). You can glue sand and rock rubble to the entrance for a natural look. My tunnel looks just like a rock cave really and you can't see any pvc.

 

[CMO]

Here's a few reference photos if it helps visualize. I used 2" PVC for a skeletor eel. In the video which is a bit old now he's still only about half grown. He's nearly double that size today and fills out the tunnel nicely now. The tunnel is about 2' long which fits his full grown length perfectly.

Font entrance

Back Entrance

 

[Goodair]

Thank you for the visuals! I think I got all the info now.
Whats left is figuring out a layout.

 

[SudzFD]

Resurrecting this thread to ask a question. I’m considering making a three opening or 2 - 2 opening tunnels for my snowflake morey. He’s small now, about 10-12” and probably 3/4” tall. Was going to make a 2ft long tunnel out of 1.5” pvc. Would that be best for him? Or should I start with 1” pvc and maybe upgrade it when he gets bigger?

My other thought was to make it with 1.5” pipe with 1” reducers on the ends that I could remove easily when he gets bigger. That way he might feel secure now like the tunnel is smaller but I can easily adjust it without removing everything if that makes sense.

Thoughts?

 

[TheAddReefer]

Resurrecting this thread to ask a question. I’m considering making a three opening or 2 - 2 opening tunnels for my snowflake morey. He’s small now, about 10-12” and probably 3/4” tall. Was going to make a 2ft long tunnel out of 1.5” pvc. Would that be best for him? Or should I start with 1” pvc and maybe upgrade it when he gets bigger?

My other thought was to make it with 1.5” pipe with 1” reducers on the ends that I could remove easily when he gets bigger. That way he might feel secure now like the tunnel is smaller but I can easily adjust it without removing everything if that makes sense.

Thoughts?

I don’t have a snowflake anymore but I do have a Fimbriated Yellow Head, a GreyFace and a Ghost Ribbon. For my ghost ribbon I used 1” pvc with 90 degree elbows on the ends, it’s the dimensions of the tank in like a U shape. He must like it because I’ve never see him, he never comes out and only sticks his head out to eat. For my frim and grey face I used 1 1/2” pvc 4’ long with 90 degree elbows. Same thing I never see him until he’s hungry. I actually saw his full body for the first time the other day and realized it’s almost time to upgrade so now I plan on upgrading the tunnels to 2’ pvc doing the u shape like I did for my ghost ribbon. All pvc buried under the sand and rock work. This has worked for me so far.