Ranco Temp Controller Question

[jpas]

Hello,

I am setting up my Ranco controller and was wonder if the temperature probe is salt water proof?

Thanks

 

[mamgm2]

have mine for almost 10years, so I guess you can say yes

 

[dmolavi]

When I ordered mine from Ranco, they sealed the probe for me.

 

[AlexG]

I have been using the stock temp probe for over a year without any issues.

 

[Muttley000]

mine is 3 years running and no issues

 

[ca1ore]

Both of mine have a plastic shield over the probe as Ranco says it’s not enduring when directly exposed to SW.

 

[reefwiser]

Yes they are using one forever.:)

 

[CC13]

Could you not just use some shrink tube and seal the probe and the wire from the salt?

 

[dmolavi]

Could you not just use some shrink tube and seal the probe and the wire from the salt?

Ranco did it at no charge for me

 

[CC13]

Ranco did it at no charge for me

Sort of off-topic but I have a Ranco I have yet top setup yet. Do they need to be calibrated?

 

[Foothill Corals]

Sort of off-topic but I have a Ranco I have yet top setup yet. Do they need to be calibrated?

No

 

[Muttley000]

Could you not just use some shrink tube and seal the probe and the wire from the salt?

Yes, I bought some food grade heat shrink tubing and cut about 3' off and put the probe in the middle and just folded the heat shrink in half with the ends out of the water. It worked fine but I read it was totally unneeded and removed it shortly after

 

[Foothill Corals]

I have used these for close to 20 years. They are very reliable but...The probe will fail if not water proofed with shrink tubing. Without the shrink tube I have had the probe last for years but I have also had one fail at around a year.

 

[thatmanMIKEson]

The only thing is they are adjustable for F° or C° in 1 degree increments, is there a way to fine tune them or is putting them in F° the smallest window for on off temperature range?

 

[jhuntstl]

The only thing is they are adjustable for F° or C° in 1 degree increments, is there a way to fine tune them or is putting them in F° the smallest window for on off temperature range?

As far as I know, that's as tight as you can tune them. I would usually see 1-2 degree degree swings with my ranco. I still use it, but I have it behind a Hydros now. I'm usually within a quarter degree nowadays.

 

[KStatefan]

The only thing is they are adjustable for F° or C° in 1 degree increments, is there a way to fine tune them or is putting them in F° the smallest window for on off temperature range?

One degree is the minimum differential

https://s3.amazonaws.com/s3.supplyh...Ranco - ETC-111000-000 - Product Overview.pdf

 

[SPS2020]

The probes come in two flavors, one of which is titanium and is fine for saltwater. The other would need to be shielded.

 

[BZOFIQ]

The probes come in two flavors, one of which is titanium and is fine for saltwater. The other would need to be shielded.

You're thinking AquaLogic which is a ranco with a titanium encapsulated probe.....and a new brand sticker.

 

[SPS2020]

You're thinking AquaLogic which is a ranco with a titanium encapsulated probe.....and a new brand sticker.

Ahhh...that's right. Ranco always defaults in my head, but AquaLogic does put their sticker on it with the titanium probe.

 

[thatmanMIKEson]

One degree is the minimum differential

https://s3.amazonaws.com/s3.supplyh...Ranco - ETC-111000-000 - Product Overview.pdf

Actually I was looking for this, which if I'm reading it correctly, it will have a smaller operating window if it is set to C° compared to being set to F°

A change of 1 degree Fahrenheit equals a change of 5/9 = 0.56 degrees Celsius. To convert a Fahrenheit temperature to Celsius, subtract 32 and multiply by 5/9.

So setting the unit to C° it would cycle on in half the temperature it takes to operate in F°

Am I correct on this?