Random Flow Generator(RFG)

Lonely reefer's · Jul 14, 2017

Hello
Have anyone else is using this product?
Just got mine and I love it!
Look at the video of my torch
No pump in the tank beside 2 RFG NOZZLES

SDdiver · Jul 14, 2017

never seen it, simple and effective looking, I've got a loc link 3/4" set up, do you think I can attach it?

Lonely reefer's · Jul 14, 2017

Yes
I order the wrong side 1"
But exchange to 3/4
The video is currently in 3/4 RFG attached to 3/4 loc line

clsanchez77 · Jul 14, 2017

Any idea what the required minimum flow is through it?

Lonely reefer's · Jul 14, 2017

Not sure,but I'm using 951 gph reture pump in my 75g tank
You can always ask vividcreativeaquatic.com

chipmunkofdoom2 · Jul 14, 2017

Interesting concept. I'd be curious to see how well this holds up to dirt and biofilm accumulation. I'm no fluid dynamics expert, but I'd imagine the mechanism that forces water through a random channel would be very susceptible to clogging and dirt buildup.

clsanchez77 · Jul 14, 2017

zoasaholic said:
Not sure,but I'm using 951 gph reture pump in my 75g tank
You can always ask vividcreativeaquatic.com

Is that 951 nominal or measured? What pump are you using and generally what size piping?

Lonely reefer's · Jul 15, 2017

chipmunkofdoom2 said:
Interesting concept. I'd be curious to see how well this holds up to dirt and biofilm accumulation. I'm no fluid dynamics expert, but I'd imagine the mechanism that forces water through a random channel would be very susceptible to clogging and dirt buildup.

It seems very easy to clean
Only time will tell

Lonely reefer's · Jul 15, 2017

clsanchez77 said:
Is that 951 nominal or measured? What pump are you using and generally what size piping?

3/4" return pipe T off to 1/2" hose at the nozzles
I probably loosing some flow at the 1/2 hose

justingraham · Jul 15, 2017

Looks to be the same concept as a penductor or enductor

To get the best out of it u would want to use a high pressure type pump like a little giant

clsanchez77 · Jul 15, 2017

justingraham said:
Looks to be the same concept as a penductor or enductor

To get the best out of it u would want to use a high pressure type pump like a little giant

Thats what it looks like to me too, the only difference being the internal helical windings. Would love to see a video/animation of how the inside works.

3mm3 · Jul 15, 2017

Thanks for the heads up on this!

293482398 · Jul 15, 2017

I got one for my reefer 170, but it seems a fail.

You have to point it down slightly to avoid a vortex into the output nozzle. However at that depth, if the power goes out, there is not enough room in the sump to hold all the water!!

I tested with an empty sump before I added my skimmer.

I keep meaning to email them, I'm guessing the other reefers have a better sump to surface area ratio?

ksfulk · Jul 16, 2017

I have a pair of them on my 525xL reefer and I like the variation in flow. I agree that they have to be lowered a bit to prevent air from being sucked in, but I havent had any issue with the sump flooding. The internals of the nozzles dont move or anything, they just basically twist the water stream as it comes out of the nozzle. Mostly I see shifts in the water flow at the top of the waterline. Im pushing ~1300 gph though the split locline.

Flameback Pair · Jul 18, 2017

Will the fit the Top Shelf Aquatics Red Sea Reefer Split Return Nozzle?

MrMichael said:
I got one for my reefer 170, but it seems a fail.

You have to point it down slightly to avoid a vortex into the output nozzle. However at that depth, if the power goes out, there is not enough room in the sump to hold all the water!!

I tested with an empty sump before I added my skimmer.

I keep meaning to email them, I'm guessing the other reefers have a better sump to surface area ratio?

Could you drill a tiny hole in the butt end of the RFG to break siphon at a higher water level thereby avoiding so much water back-siphoning into the sump of my RSR 250? I would use two RFGs on a TSA split return.

Midrats · Nov 27, 2017

MrMichael said:
I got one for my reefer 170, but it seems a fail.

You have to point it down slightly to avoid a vortex into the output nozzle. However at that depth, if the power goes out, there is not enough room in the sump to hold all the water!!

I tested with an empty sump before I added my skimmer.

I keep meaning to email them, I'm guessing the other reefers have a better sump to surface area ratio?

I love mine on my REEFER Nano. It's the sole source of flow and it moves my LPS like a pulsing Tunze. Vortices can easily be defeated by adjusting the infinitely adjustable nozzle. The ball socket on the REEFER is multi-directional. The RFG adapter can be rotated left and right, and the RFG nozzle is on a ball socket. It takes a bit of adjusting, don't give up on it. Rotating the adapter to the right to get the assembly closer to the surface and adjusting the nozzle to the left aimed slightly towards the surface is my sweet spot. Mine is right near the surface without a vortex in sight. Plenty of room in the sump too when the power is off, nowhere near a flood.

Unless you have an oversized return pump, manifolds, and all kinds of equipment draining when the power goes out, I'm not sure what the problem is.

Zwogle · Nov 28, 2017

I'm a fan, have two 1/2" on my 33gal, I don't know if it's a real game changing addition, but i'll take a little more current variation.

ca1ore · Nov 28, 2017

I think it's a nice evolution of the standard educator. Also nice that the larger model slip fits over standard 1" PVC pipe (not a fan of locline). I'm using a pair on my closed loop so no worries about back siphon.