Red Sea Reefer P650 Cabinet Door Hinges

BRS

psumms

Active Member
View Badges
Joined
Sep 11, 2019
Messages
150
Reaction score
83
Location
United Kingdom
Anyone know the part number for replacement cabinet door hinges on a Red Sea Reefer Peninsula 650? Mine are pretty well rusted up and i'm having problems getting getting the info from Red Sea! Ideally looking for original Red Sea replacements - unless there is a know (Reliable) compatible manufacturer?
 
Avast

JDowns

Valuable Member
View Badges
Joined
Oct 6, 2017
Messages
1,223
Reaction score
2,657
Location
Phoenix
If you look on the backside of the cup there should be a stamped number. Most likely "304".

IMG_2894.JPG



If you google search for a 304 stainless steel cabinet hinge you should be able to find your match. These hinges are widely copied and can vary. You need to measure the cup, the part of the hinge that recesses into the door or the hole in the door itself. Most likely your cup is 35mm diameter with a 13mm depth. I haven't seen how the doors work on your model but I'm assuming a 110 degree opening with a full overlay. I would bet a Blum Cliptop 110 with a full overlay would work for your situation. Otherwise just google "cabinet door hinge 304" and pay attention to the cup diameter / depth, angle of opening, and overlay.
 

JDowns

Valuable Member
View Badges
Joined
Oct 6, 2017
Messages
1,223
Reaction score
2,657
Location
Phoenix
If you look on the backside of the cup there should be a stamped number. Most likely "304".

IMG_2894.JPG



If you google search for a 304 stainless steel cabinet hinge you should be able to find your match. These hinges are widely copied and can vary. You need to measure the cup, the part of the hinge that recesses into the door or the hole in the door itself. Most likely your cup is 35mm diameter with a 13mm depth. I haven't seen how the doors work on your model but I'm assuming a 110 degree opening with a full overlay. I would bet a Blum Cliptop 110 with a full overlay would work for your situation. Otherwise just google "cabinet door hinge 304" and pay attention to the cup diameter / depth, angle of opening, and overlay.
Pay attention to the overlay! If the door is an end door that overlays the cabinet edge fully then a full overlay. If the door is in the center and shares an overlay with another door on a cabinet edge it may be a half overlay.
 
OP
psumms

psumms

Active Member
View Badges
Joined
Sep 11, 2019
Messages
150
Reaction score
83
Location
United Kingdom
IMG_0638 (1).jpg
Thanks @JDowns very helpful info. I've searched previously for a close match based on the cup dimensions but never been able to find a hinge with the four holes in the plate:
 
Fritz

JDowns

Valuable Member
View Badges
Joined
Oct 6, 2017
Messages
1,223
Reaction score
2,657
Location
Phoenix
IMG_0638 (1).jpg
Thanks @JDowns very helpful info. I've searched previously for a close match based on the cup dimensions but never been able to find a hinge with the four holes in the plate:


Not sure, but judging by the picture that looks like an inset hinge, the door sits inside the frame, so no overlay.

Something like these:



This last one appears to be a close match. You would have to check dimensions.

 
BRS

WHAT DOES THE TERM "GOOD WATER QUALITY" MEAN TO YOU?

  • Your aquarium water is in acceptable ranges measured by consumer level water tests

    Votes: 16 44.4%
  • Your aquarium water is in acceptable ranges measured by ICP type testing

    Votes: 1 2.8%
  • Your aquarium water is good based on how your corals are growing and look

    Votes: 18 50.0%
  • Your aquarium water is good based on how little nuisance algae is growing

    Votes: 6 16.7%
  • Your aquarium water is good based on how it looks to you

    Votes: 6 16.7%
  • Other (please explain in the thread)

    Votes: 1 2.8%
Top