Reef octopus ozone generator

[leon.1980]

Ok guys. I have a reef octopus 150 not classic. Want to run ozone on it. Plan is to use a t valve right at the Venturi and out the ozone on that. Desiccant to ozone (Poseidon 200) to Venturi.
I already have a co2 scrubber on it too.
picture for t valve example.
Any problems for seen with this?

 

[blaxsun]

Different skimmer, but I run the ozone into the top outlet on the silencer. I think a T-valve should work (assuming you plan to feed both the ozone and Co2 lines into the same outlet on the silencer?)

 

[leon.1980]

Different skimmer, but I run the ozone into the top outlet on the silencer. I think a T-valve should work (assuming you plan to feed both the ozone and Co2 lines into the same outlet on the silencer?)

So the co2 is off the silencer. However I’ve been told you want to run ozone as close to the Venturi as possible.

 

[blaxsun]

So the co2 is off the silencer. However I’ve been told you want to run ozone as close to the Venturi as possible.

No idea - I just run my ozone into the silencer and let it get sucked in.

 

[Miami Reef]

Plan is to use a t valve right at the Venturi and out the ozone on that. Desiccant to ozone (Poseidon 200) to Venturi.
I already have a co2 scrubber on it too.

That works.

CO2 scrubbers work best with damp air, while Ozone is better with dry air: A but of a conundrum, but IMO Ozone doesn’t need to run 24/7 to get the benefits.

I only run Ozone 1-2x per week, and my water is crystal clear.

 

[acropora4u]

That works.

CO2 scrubbers work best with damp air, while Ozone is better with dry air: A but of a conundrum, but IMO Ozone doesn’t need to run 24/7 to get the benefits.

I only run Ozone 1-2x per week, and my water is crystal clear.

what is your ozone set up ?

 

[Miami Reef]

what is your ozone set up ?

Air drier > Ozotech Poseidon > Regal 250INT skimmer through the air silencer.

 

[WhatCouldGoWrong71]

Air drier > Ozotech Poseidon > Regal 250INT skimmer through the air silencer.

@Miami Reef @blaxsun Do you run carbon in the water near the skimmer and/or does water run through carbon before it returns to the display? Meaning, do you remove the ozone from the water before it hits the display? In reading through threads on R2R it would feel like some evolution has happened and I can't appear to get a good read on best practice. I set mine up for the first time yesterday. I won't comment on my ORP values, as I am simply going to order a new ORP probe, mine is a couple years old with zero attention to it. The trend though is moving opposite of my PH. I currently have carbon/GFO pump parked next to my skimmer and I have carbon set up prior to hitting my return chamber. It's been running since last night. Seeing how people only run it for an hour or two a week, I am thinking about turning it off. However, I only have it as close to off without turning off (its a P 200) and I am not using a dryer, so the ozone isn't as potent.

Thoughts?

 

[Miami Reef]

I just have activated carbon in the sump after the skimmer, but it’s not directly on the output of the skimmer. Works well for me.

I run ozone for 1-2 days out of the week. I could run it longer, but there’s no need IMO. :)

I use an air drier now. I’m getting much better efficiency with ozone, since I live in a humid area.

 

[leon.1980]

That works.

CO2 scrubbers work best with damp air, while Ozone is better with dry air: A but of a conundrum, but IMO Ozone doesn’t need to run 24/7 to get the benefits.

I only run Ozone 1-2x per week, and my water is crystal clear.

Cant I just run it through the co2 media then dry it? Air comes in from outside line runs through co2 media while not dried, then it gets dried after the co2 media by the seas isn’t then it runs through the ozone generator.

 

[zoomonster]

I run air pump->Ozotech air dryer->Ozotech Poseidon 200->one of the two air silencer ports on Reef Octopus XP3000I. Just use carbon mat and bag of carbon on top of the skimmer and carbon bag in sump. You could probably just stick a CO2 scrubber inline before the air dryer.

 

[WhatCouldGoWrong71]

Just a regular air pump?

 

[zoomonster]

Just a regular air pump?

Yes, I just run an Eheim 400 dual port with both connected to a Y fitting that steps up the two to the larger airline into the dryer.

 

[leon.1980]

I run air pump->Ozotech air dryer->Ozotech Poseidon 200->one of the two air silencer ports on Reef Octopus XP3000I. Just use carbon mat and bag of carbon on top of the skimmer and carbon bag in sump. You could probably just stick a CO2 scrubber inline before the air dryer.

What would you need an air pump for if it’s on the skimmer? I see Poseidon 200 running off the skimmer only all the time online.

 

[blaxsun]

@Miami Reef @blaxsun Do you run carbon in the water near the skimmer and/or does water run through carbon before it returns to the display? Meaning, do you remove the ozone from the water before it hits the display? In reading through threads on R2R it would feel like some evolution has happened and I can't appear to get a good read on best practice. I set mine up for the first time yesterday. I won't comment on my ORP values, as I am simply going to order a new ORP probe, mine is a couple years old with zero attention to it. The trend though is moving opposite of my PH. I currently have carbon/GFO pump parked next to my skimmer and I have carbon set up prior to hitting my return chamber. It's been running since last night. Seeing how people only run it for an hour or two a week, I am thinking about turning it off. However, I only have it as close to off without turning off (its a P 200) and I am not using a dryer, so the ozone isn't as potent.

Thoughts?

Yes, I run a carbon reactor adjacent to the skimmer as well as a Stink Sink filled with dry carbon on top of the skimmer.

 

[pcorpion]

Air drier > Ozotech Poseidon > Regal 250INT skimmer through the air silencer.

Can you show me your setup ? I would like to run ozone will you show me take pics of your setup do I can copy it ? Thanks brother

 

[Bent17]

interested to see your setup!

 

[Luisn17]

Air drier > Ozotech Poseidon > Regal 250INT skimmer through the air silencer.

@Miami Reef by chance do you have a pic of your setup? I plan to do the same and run a 15-20 burst of ozone at night. Did you notice any changes to the white hose with the use?

Thanks!

 

[Miami Reef]

@Miami Reef by chance do you have a pic of your setup? I plan to do the same and run a 15-20 burst of ozone at night. Did you notice any changes to the white hose with the use?

Thanks!

My setup is very simple. The ozone generator comes with input and output nozzles.

The input is where air enters the machine.

The output tube goes in the skimmer venturi or air silencer. The skimmer will suck the air from the ozone unit.

 

[X-37B]

I run ozone on a Tunze 9430dc. It sits in the return chamber, and I run no carbon or air dryer.
Posiedon set at 3 with small air pump pushing it through.
This replaced my Mutiny reactor.
The ozone it teed into the silencer.
Orp set at 375 now and runs 375 to 400.
This works as well as the Mutiny reactor in keeping the water clear, imo.
Just took these.