reef-pi :: An opensource reef tank controller based on Raspberry Pi.

[Ranjib]

As I'm looking at it closer it looks like @Schreiber and I are having the same issue. I can confirm that all was working with my current PCA9685 board at PWM 1500 until a reboot today. I removed the database, and started troubleshooting from scratch. Every time I enable the PCA9685 board and reload, reef-pi crashes and will not start again.

Ack. Let me test it out with 1500 frequency settings.

 

[sfgabe]

Ack. Let me test it out with 1500 frequency settings.

journalctl:

Oct 27 14:18:00 ReefControlPi systemd[1]: Started raspberry pi based reef tank controller.
Oct 27 14:18:00 ReefControlPi reef-pi[311]: 2019/10/27 14:18:00 Setting pca9685 frquency: 1500
Oct 27 14:18:00 ReefControlPi reef-pi[311]: 2019/10/27 14:18:00 ERROR: Failed to initialize pca9685 driver with mock i2c bus.
Oct 27 14:18:00 ReefControlPi reef-pi[311]: 2019/10/27 14:18:00 ERROR: Failed to initialize controller. Error:remote I/O erro
Oct 27 14:18:00 ReefControlPi systemd[1]: reef-pi.service: Main process exited, code=exited, status=1/FAILURE
Oct 27 14:18:00 ReefControlPi systemd[1]: reef-pi.service: Failed with result 'exit-code'.

 

[sfgabe]

Ack. Let me test it out with 1500 frequency settings.

I dont think that's the issue. I've downgraded to 2.3 and the issue is the same. It looks like the problem is coming from upgrading to the latest version of rasbian (Raspbian GNU/Linux 10 - buster) or some related module upgrades. This same 2.3 setup was working on Stretch Lite for almost a year, now with Buster + 2.3 it fails.

 

[Schreiber]

@sfgabe , do you have any of the address pins soldered on your PCA9685 board? I was able to fix my issue by reverting to the default 0x40 address.

 

[sfgabe]

@sfgabe , do you have any of the address pins soldered on your PCA9685 board? I was able to fix my issue by reverting to the default 0x40 address.

No, default setup. Always showed up at 40/70 address previously.

 

[BenB]

reef-pi :: An opensource reef tank controller based on Raspberry Pi.

It is the web browser. Clearing cache and local storage in the browser for the reef-pi website may solve it. I think I had suggested these. Like hard refresh or access reef-pi ui from incognito mode

www.reef2reef.com

Looks Like version 2.x does not support an other adress then 0x40, maybe better to move to 3.0

 

[Schreiber]

reef-pi :: An opensource reef tank controller based on Raspberry Pi.

It is the web browser. Clearing cache and local storage in the browser for the reef-pi website may solve it. I think I had suggested these. Like hard refresh or access reef-pi ui from incognito mode

www.reef2reef.com

Looks Like version 2.x does not support an other adress then 0x40, maybe better to move to 3.0

Man, knowing that would've saved me a solid 10 hours of troubleshooting, lol. ;Blackeye Oh well, it works now! Note to self, 1% of the time, I'm *not* the problem! Is 3.0 stable, or are there known bugs at the moment I should know about?

 

[Schreiber]

Tonight is just full of surprises. Hooked up one of @Michael Lane 's pH boards & I cannot get any readings from my probe. It's just stuck at 0.

I have both jumpers on the board & i2cdetect sees the board at 0x45. I'm using the PINPOINT Marine probe, brand new. Just unboxed it. Is there a way to verify the probe itself isn't the problem?

I calibrated it using 6.86 solution for the midpoint value & 9.18 as the high point. One bit of weirdness I noted was that when I typed those values in, it asked me to select a valid value. For example, for the midpoint, I typed 6.86, it highlighted the box red & said the closest valid values were 6.86 & another number, can't remember. The only way I could get it to proceed was if I used the arrows to increase to 7.86, then decrease back to 6.86.

 

[Michael Lane]

Tonight is just full of surprises. Hooked up one of @Michael Lane 's pH boards & I cannot get any readings from my probe. It's just stuck at 0.

I have both jumpers on the board & i2cdetect sees the board at 0x45. I'm using the PINPOINT Marine probe, brand new. Just unboxed it. Is there a way to verify the probe itself isn't the problem?

I calibrated it using 6.86 solution for the midpoint value & 9.18 as the high point. One bit of weirdness I noted was that when I typed those values in, it asked me to select a valid value. For example, for the midpoint, I typed 6.86, it highlighted the box red & said the closest valid values were 6.86 & another number, can't remember. The only way I could get it to proceed was if I used the arrows to increase to 7.86, then decrease back to 6.86.

I don't have anything to add to the calibration comment, but reef-pi uses decimal for the address instead of hex. Instead of 0x45, try using 69 instead.

 

[hotdrop]

is anyone selling custom reef Pi boards that are already setup for temperature and ph monitoring? I remember some pictures floating around this thread earlier.

 

[dmolavi]

@theatrus is, but you need reef-pi 3.0 (currently in alpha) for pH monitoring.

 

[burningbaal]

Okay, starting to get mine together, my adj strip is running!

Two questions: with multiple temperature sensors, can you have it alert when they differ by more than, say 1 degree c? If not, I may just set up one to control 77-80 and the other alert and control 76-81?

Second: mechanical relays are more prone to failure than solid state, right? Solid state struggle with low loads. So maybe I could add a solid state relay in addition to the adj strip to control my heaters? Low likelihood of failure and not a low load..seem good?

 

[burningbaal]

is anyone selling custom reef Pi boards that are already setup for temperature and ph monitoring? I remember some pictures floating around this thread earlier.

I bought @Michael Lane 's hat on tindie and am very happy so far!

 

[BenB]

Tonight is just full of surprises. Hooked up one of @Michael Lane 's pH boards & I cannot get any readings from my probe. It's just stuck at 0.

I have both jumpers on the board & i2cdetect sees the board at 0x45. I'm using the PINPOINT Marine probe, brand new. Just unboxed it. Is there a way to verify the probe itself isn't the problem?

I calibrated it using 6.86 solution for the midpoint value & 9.18 as the high point. One bit of weirdness I noted was that when I typed those values in, it asked me to select a valid value. For example, for the midpoint, I typed 6.86, it highlighted the box red & said the closest valid values were 6.86 & another number, can't remember. The only way I could get it to proceed was if I used the arrows to increase to 7.86, then decrease back to 6.86.

Ok, so you are using the opensource ph board. This will not work on 2.4 and it requires 3.0 onwards. Support for this driver was done recently and its scheduled to be available for public release later this year. You can use the 3.0 testing builds to use the ph board but calibration is still not supported via the UI yet. @Michael Lane is working on this (calibration support via UI), but its not ready yet

It looks like you need reef pi 3.0 for @Michael Lane's pH boards.

 

[Schreiber]

I don't have anything to add to the calibration comment, but reef-pi uses decimal for the address instead of hex. Instead of 0x45, try using 69 instead.

Just tried that... No luck. I'm getting this error every time I try to calibrate.

Here's the journal

Still getting the please select a valid value error as well.
I've reset the database a few time now. Once I get back in about 30 minutes, I'll be downgrading to 2.4 & if that doesn't work, I'll try 3.0.0 v2.

 

[Michael Lane]

Yes, there was a calibration bug fixed in August. I don't believe it is packaged into a release yet, but I think a new alpha release it's coming soon.

In the meantime, calibration would have to be done via the command line.

 

[Schreiber]

Yes, there was a calibration bug fixed in August. I don't believe it is packaged into a release yet, but I think a new alpha release it's coming soon.

In the meantime, calibration would have to be done via the command line.

Ahhhh, after digging through tons of posts, I finally pieced together how to do this, lol. I'll post the consolidated, & corrected instructions here for future pioneers with a few additions that could help. I'll replace any mentions of IP with a generic IP of 192.168.x.x, use your raspberry pi's IP instead. If you don't know it, go to the terminal & type ifconfig, then press enter.

• Wire up your ph board and power up your raspberry pi. Once up,you should see the ph board regisetered as i2c addres 0x40 (64 in decimal). Type i2cdetect -y 1 into terminal & press enter. The default address for your board may be different (the @Michael Lane one is 45 with both jumpers attached). It will appear in this list.
  
  
  
• Next download and install the 3.0 pre-alpha release. Make sure to delete the old database. In terminal, use the following commands:
• sudo systemctl stop reef-pi.service
• sudo rm -rf /var/lib/reef-pi/reef-pi.db
• sudo systemctl start reef-pi.service
  • Details can be found in the troubleshooting guide
• Once running , go ahead and create a new driver from the Configuration -> Drivers section, select phboard as type (pico board for pico base board users).
• Make sure to click on the drop down and select the type, even if the one shown in the UI by default is the one you are using (i.e. do an explicit selection).
• My UI gave an error if i had a space in the Name, may just be me though.
• Your address is in decimal format. Look up a "Hex to decimal convertor" & type in your address from the i2cdetect command (e.g. 0x40) & convert it. 0x45 = 69.
• Specify a name, keep it unique across different drivers.
  
  
  
• Next, create a connector under analog input section and associate it with the new driver, specify channel as "0" and give it a name.
  
  
  
• Next, create a pH monitor (if you dont see ph tab, then probably its not enabled, enable this module under Configuration -> Settings, and reload reef-pi).
• Associate the ph monitor with the newly created analog input. And that's it, you should see your ph sensors reading. Note, without calibration it will emit sensor values in raw millivolts, which for me is around -8K.
  
  
  
• Time to perform calibration (don't use the button, we've got to use a work around).
• If you are using reference solution (like ph 7 and 10), keep them in tank temperature and immerse probe in them and note down the reading from the dashboard. It will take a few minute to stabilize the reading. For example, if you put it in 8.21 pH solution, you may get a reading fluctuating around -8768.
• We'll be applying the calibration via API (due to UI still being worked on).
• Go to your pi's file manager, right click, create a new file, name it calibration.json containing the calibration data in this format.

[
{"expected":8.21, "observed": -8768},
{"expected":8.12, "observed": -8189}
]

• The example shows my two point calibration again my own tank water with reference reading taken from hanna ph checker.
• DISABLE the pH monitor before continuing.
• In terminal, type the following 2 commands (pressing enter after each)
  
  curl -c cookie.txt -X POST -d '{"user":"reef-pi", "password":"reef-pi"}' http://127.0.0.1/auth/signin
• you will get a return of "null"- this is good.
  curl -X POST -d @calibration.json -b cookie.txt http://192.168.x.x/api/phprobes/1/calibrate
• If you've had multiple attempts at creating a pH monitor, your pH monitor ID may not be 1. If you want to check, use the following command in terminal:
  • curl -b cookie.txt http://192.168.x.x/api/phprobes/

You can now go back to your UI, enable the pH probe, then watch the output to see if it's an actual pH value now!

 

[Schreiber]

Is there a good way to obtain the raw mV value from a pH probe without having to delete the calibration file? Or is that the best way to go about it?

 

[burningbaal]

So I tried to set up a timer to run the ATO for 5 minutes every hour (it runs so often now and is kinda loud as it splashes in), but can't quite figure out the configuration. Any advice?

 

[burningbaal]

So I tried to set up a timer to run the ATO for 5 minutes every hour (it runs so often now and is kinda loud as it splashes in), but can't quite figure out the configuration. Any advice?

I should note the ATO is just a relay outlet, not a reef-pi ATO