Return plumbing help

  • Thread starter Thread starter HiImSean
  • Start date Start date
  • Tagged users Tagged users None

HiImSean

Active Member
View Badges
Joined
Jan 20, 2012
Messages
370
Reaction score
218
Location
Acworth, GA
What state or country do you live in
Georgia
Rating - 0%
0   0   0
I’m kind of stuck on what to do for my return plumbing. I have a manifold I built with 3 1/2 gate valves and one will have a 3/4” gate valve. On the one side I have a 4way. It will feed the manifold, allow for a return from a uv sterilizer, and then flow to the tank. The part I’m not so sure about is the return feed from the uv. Instead of a 4 way, I could do two Ts and plumb the return in that way. I plan on using tubing to connect the return pump to and from this manifold setup.

E352025E-67E4-4420-81AE-137B68012F68.jpeg 686BA9B2-7F06-4227-A819-A73DEB1D2A92.jpeg
 
Are you planning to have your UV drain run back into the manifold? I would use one of the valves from your manifold (3/4”)to feed the UV and scratch the 4 way.
 
You can’t have the feed for uv and return from uv back to the same manifold because the manifold is pressurized
 
Sorry if I wasn’t making sense. The last port on the manifold doesn’t have a gate valve and will feed the uv and will be 3/4”. One of the 1/2” will feed my algae scrubber and the other two will be extra for now. The uv return will come in where the ball valve is located.

The 90 degree turns on the 4way would come from the return pump and go to the tank once I get barbed fittings.

4A7E0D80-0938-4DBF-BD38-64A05B0A4DD9.jpeg
 
Sorry if I wasn’t making sense. The last port on the manifold doesn’t have a gate valve and will feed the uv and will be 3/4”. One of the 1/2” will feed my algae scrubber and the other two will be extra for now. The uv return will come in where the ball valve is located.

The 90 degree turns on the 4way would come from the return pump and go to the tank once I get barbed fittings.

4A7E0D80-0938-4DBF-BD38-64A05B0A4DD9.jpeg
No workie
 
Sorry if I wasn’t making sense. The last port on the manifold doesn’t have a gate valve and will feed the uv and will be 3/4”. One of the 1/2” will feed my algae scrubber and the other two will be extra for now. The uv return will come in where the ball valve is located.

The 90 degree turns on the 4way would come from the return pump and go to the tank once I get barbed fittings.

4A7E0D80-0938-4DBF-BD38-64A05B0A4DD9.jpeg
This won’t work because your pump will push water to both ends of your Uv
 
A886C085-8304-4E6F-AD6A-DA9B91928A80.jpeg

you could scratch the uv return and the design will function. You’ll just need to add some hose or pvc to your UV output. You will lose stable pressure to your Uv because it’s at the end of your manifold. But diligent maintenance to your equipment can mitigate the pressure fluctuations.
 
Would sooner run single pump for uv, and a single pump for return so you know how many gph you have to these items. Using a manifold for other items is less critical, as far as knowing how many gph. Manifolds look cool, and can save space/pumps, but without flow meters to each device it’s a guess at best
 
How would you plumb the return of the uv?
With a flex hose and at the end I would attach It to two 90'elbows to act as a hook for the rim of my tank. Or if I was going full custom I would drill a bulkhead into the back wall of my tank just for the uv output.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 21 25.6%
  • I’d trust someone who knows my tank to choose

    Votes: 8 9.8%
  • I’d rather get a gift card and pick it myself

    Votes: 30 36.6%
  • I’d prefer gear or supplies instead

    Votes: 2 2.4%
  • Please don’t surprise me with livestock

    Votes: 21 25.6%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new