Sam's Oceanic 120 - DIY solutions

[rmorris_14]

are those eggs from the babies?

 

[Projects with Sam]

are those eggs from the babies?

yes! those are the ones that wouldn't fit in the male's mouth! not sure they're viable but I'll keep bubbling them.

I think there are two pairs in the frag tank

 

[tbrown]

yes! those are the ones that wouldn't fit in the male's mouth! not sure they're viable but I'll keep bubbling them.

I think there are two pairs in the frag tank

A couple of them look like they may be, at least in my experience with freshwater fish eggs. Several do look like duds.

 

[Projects with Sam]

The egg-mass was stuck to the top of the bubbler this morning. I've never had much success bubbling... I'll wait 2 weeks then strip him.

 

[tbrown]

Turn the air down some. They should gently bounce... If the water is passing over them it may be ok that they're at the top but I'd assume it's too much flow. Are they still yellow or turning white?

 

[Projects with Sam]

PhotoDump!
New Product in Development!

My APril BC growout entries!

Top Downs:

Royal Grammar

\]
Windex!

 

[Projects with Sam]

Only 4 links on signatures and I want to keep track of my grow-out posts... so I'll do it here and link to this post.

2023 SpaceLaser:	March	April
2023 Rainbow's Army:	March	April

 

[tbrown]

Only 4 links on signatures and I want to keep track of my grow-out posts... so I'll do it here and link to this post.
2023 SpaceLaser: March April
2023 Rainbow's Army: March April

Edit the first post on this thread with the links.

 

[Projects with Sam]

Edit the first post on this thread with the links.

ya.... i screwed that up too though... made my first post sooooo long I have to scroll so far...

 

[Nate Chalk]

PhotoDump!
New Product in Development!

My APril BC growout entries!

Top Downs:

Royal Grammar

\]
Windex!

The random flow generator looks niiiice. Gotta be better than my flared nozzle

 

[Projects with Sam]

https://www.youtube.com/shorts/g_lJaHpVCkk

 

[Projects with Sam]

https://www.youtube.com/shorts/pgtu5es2vOk

 

[F i s h y]

@Projects with Sam thank you for the care package! Ordering from your website was super easy and the 1.5 inch strainers are perfect! And thanks for the extras. Love the frag holders!

 

[Projects with Sam]

@Projects with Sam thank you for the care package! Ordering from your website was super easy and the 1.5 inch strainers are perfect! And thanks for the extras. Love the frag holders!

Thanks! Those were some of the last prints on my un-updated printers; I'm able to get better quality now. I may give you 2 of the updated ones next time I see you in-person as a point of pride!
Its like when you do yardwork and you get one section of your yard looking really nice... makes the rest look wanting.

 

[Projects with Sam]

I found cheap BL Touch sensors that work ok so have been updating my printers. So far I have the Ender3 Pro 400, an Ender 3 Pro, and now my CR-10 updated. I am adding direct drive extruders with down-sized steppers (weight) where I can.
All of this requires I compile Marlin for each printer.
Wondering if I should have just did the jump to Klipper for input shaping.

I also upgraded the CR-10 Motherboard to a BTT SKR Mini E3 v2 and touchscreen display.

 

[F i s h y]

I found cheap BL Touch sensors that work ok so have been updating my printers. So far I have the Ender3 Pro 400, an Ender 3 Pro, and now my CR-10 updated. I am adding direct drive extruders with down-sized steppers (weight) where I can.
All of this requires I compile Marlin for each printer.
Wondering if I should have just did the jump to Klipper for input shaping.

I also upgraded the CR-10 Motherboard to a BTT SKR Mini E3 v2 and touchscreen display.

This is Jibberish... but sounds like you are having fun and enjoying it :)

 

[Projects with Sam]

This is Jibberish... but sounds like you are having fun and enjoying it :)

I did! But I didn't record any of it for the YouTube channel... oops.

 

[rmorris_14]

This is Jibberish... but sounds like you are having fun and enjoying it :)

 

[Mschmidt]

I found cheap BL Touch sensors that work ok so have been updating my printers. So far I have the Ender3 Pro 400, an Ender 3 Pro, and now my CR-10 updated. I am adding direct drive extruders with down-sized steppers (weight) where I can.
All of this requires I compile Marlin for each printer.
Wondering if I should have just did the jump to Klipper for input shaping.

I also upgraded the CR-10 Motherboard to a BTT SKR Mini E3 v2 and touchscreen display.

 

[F i s h y]

I married that chick ;) Love me some Max...