Thanks! I waited until it was to this point to create the build thread so I'm done with the build part for now.Beautiful tank Sir, thank you for creating this thread!! Following
Last edited:
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Thanks! I waited until it was to this point to create the build thread so I'm done with the build part for now.Beautiful tank Sir, thank you for creating this thread!! Following
Thanks. Yes, it started out as a cost-saving measure. I may not have saved a lot of money at the end of the day but I did get exactly what I wanted. It took me several months to complete it.Great job on the craftsmanship. I also built my own stand and would recommend building your own if you have the space and time.
At ePlastics in San Diego (Kearny Mesa area). I think they have an online store too.Where'd you get the starboard? I made a cover out of plexie and it warps when it gets wet. I need something to replace it with
At ePlastics in San Diego (Kearny Mesa area). I think they have an online store too.
Bummer. Keep looking, it is great stuff. It does warp very slightly but nothing like acrylic.Too bad shipping costs from them is more than the single sheet I need
Thanks. Yeah, i probably saved enough money on the stand to pay for the new Dewalt table saw and then some. Mostly I used an old Delta chop saw though. The Craig pocket screw jig is awesome. One lesson learned on the stand: Don't assume that all 2x6s are exactly the same (5-1/2 inch) width. They vary by up to 1/4". Best to rip them all to the same exact width on a table saw before using them.it pays to have tools you did a great job on the stand I love the support on the top
I think the cutting board material is good. It might be a bit thick but what the heck.For my sump, being in my basement, I am trying to keep the heat in and the plexi has helped a lot. I was thinking about just getting some white cutting boards and cutting them to what I need until you posted.
Nice shop! By all accounts, Reef Savvy tanks are industry-leading. Having a bullet-proof tank from a company like that will give you peace of mind, especially if it's a big one.
this is my small personal shop I built domino tables and spearguns I love being able to make everything my self
soon I will be making my tank at least 80% DIY is debating if I make my tank my self o get it done by my friend Felix at reef savvy here in Miami I know Felix since he starter making tanks I use to make sumps and reactors for some of the local stores
Thanks. I wish I had a space I could use behind the wall. In my case its a hallway to the laundry and garage. I will eventually run 1/4" RO tubing through the wall and out to the garage where I have my RO system and mixing station so I can eliminate the 10-gallon ATO reservoir. I hate having to fill that up twice a week.Nice!
I have a sort-of similar system, Planet Aquarium, 60" x 30" x 18" (I like short and wide). Peninsula style, but I was able to push the sump and supporting equipment through the wall to a closet behind it. I did a steel stand, with a decorative shelf around it... I plan to start building bookshelf units to fill in under the stand this spring. (my shop is unheated...)
Thanks. I wish I had a space I could use behind the wall. In my case its a hallway to the laundry and garage. I will eventually run 1/4" RO tubing through the wall and out to the garage where I have my RO system and mixing station so I can eliminate the 10-gallon ATO reservoir. I hate having to fill that up twice a week.
Nice to see your build thread! As you may or may not remember, I have the exact same tank as you. I FINALLY got mine running a couple weeks ago. I'll be updating my build thread as soon as I get a chance to take some pics. I like your aquascape. I went barebottom on mine, primarily because it's SPS only and has A LOT of flow.[/QUOT
Thanks, I'm looking forward to seeing yours. Yes, I remember well. You had to get it down into the basement. For the aquascape, I didn't want to skimp on rock and I wanted at least two separate mounds with a canyon between them which I was able to do. I wanted an island too but sort of ran out of space. I actually didn't spend much time on the aquascape, just started stacking rocks loosely until they were gone. There are a lot of voids and caves in the mounds and the fish have plenty of room to swim around inside them, hide and sleep. Debated doing bare bottom. I have that on my 55 gallon QT system and it is nice if you have enough flow to keep it clean. That tank has one MP40 and it does the job.
Yeah, my wife wasn't real excited about giving up our hall closet... I despise working on my knees... I'm too old and fat for that anymore. This was the only way I could come up with where I never again have to bend down to do regular maintenance. Bought a coat tree for the hallway
Do a bit of investigation before you toss out that ATO reservoir. RO/DI systems work better when they're running for a substantial amount of time. Just hooking the RO/DI system to a solenoid and float switch works... but you won't get the same kind of results you get when you can run the system for an hour or two at a time.
Just because you have a reservoir doesn't mean you have to manually fill it. Mine runs on a timer... solenoid opens every other day, for 2 hours. Water line into the reservoir goes through a float valve, which normally stops the water when full. A float switch, above the float valve, wired into the solenoid directly, will cut power to the NC solenoid if the float valve fails. So... 5g reservoir, refills all by itself every other morning. RO/DI system runs about 2 hours every time it starts up.
I just picked up a few horizontal float switches, and built a DIY breakout box for my Apex. Going to tie the ATO refill to the Apex, so that I've got a little more control and visibility into the process.
Nice to see your build thread! As you may or may not remember, I have the exact same tank as you. I FINALLY got mine running a couple weeks ago. I'll be updating my build thread as soon as I get a chance to take some pics. I like your aquascape. I went barebottom on mine, primarily because it's SPS only and has A LOT of flow.