Aquarium Rack - Overflow Plumbing Question

  • Thread starter Thread starter drbogger
  • Start date Start date
  • Tagged users Tagged users None

drbogger

Active Member
View Badges
Joined
Apr 24, 2019
Messages
165
Reaction score
126
Location
Ballston Spa, New York
What state or country do you live in
New York
Rating - 0%
0   0   0
So I am working on making a aquarium rack that will hold 8 x 20 Gallon Tanks..

I am planning on drilling the back of each tank, and install a bulkhead (Single drain design).

I have designed these overflow boxes using my laser cutter (see photos).

My question is:
- What should I do for a silencer (if any)?

Noise is not much of a concern as this setup will be in my basement, but I don't want it to be unbearably loud either.

Any ideas?
20190513_205648.jpeg
20190513_205632.jpeg
 
Drill a second drain would be the best bet, and safer too.
Stockman standpipe the best option for single drain
 
Drill a second drain would be the best bet, and safer too.
Stockman standpipe the best option for single drain
Unfortunately, I won't have enough room inside the tank for a stockman standpipe.

I was thinking something that could go on the plumbing on the outside rear of the tank... Like where the plumbing exits the tank..
 
My glasshloes overflow had a piece of acryclic that sat inside the box and acted as a "ramp" to let that water smoothly flow down through the box rather than "falling" over the teeth. maybe something as simple as that would work
 
Unfortunately, I won't have enough room inside the tank for a stockman standpipe.

I was thinking something that could go on the plumbing on the outside rear of the tank... Like where the plumbing exits the tank..
Yes. Outside the tank you could put a tee instead of elbow. With small hole drilled into cap on topside of that tee, with airline going into small hole, and an air valve on that hose. You would have to adjust to find sweet spot, and if all tanks are fed by same return...
Drill second drain, be done, be safer
 
Last edited:
My glasshloes overflow had a piece of acryclic that sat inside the box and acted as a "ramp" to let that water smoothly flow down through the box rather than "falling" over the teeth. maybe something as simple as that would work
That’s a good idea. The height of the plumbing inside the box would accomplish the same thing. If the water level inside box isn’t much lower than outside the box then it doesn’t have far to fall and won’t make noise.
The issue that is harder to address is with a single pipe drain, air and water goes down the same pipe, making gurgling noise.
If you can fashion a way to restrict the air, then you can make it quieter, but it will be sensitive to fluctuations in gph
 
Last edited:
That’s a good idea. The height of the plumbing inside the box would accomplish the same thing. If the water level inside box isn’t much lower than outside the box then it doesn’t have far to fall and won’t make noise.
The issue that is harder to address is with a single pipe drain, air and water goes down the same pipe, making gurgling noise
the overflow im speaking of was a single drain.... it wasnt overly loud sice inside the box the water flowed down the ramp and the air passed by the sides of the ramp...... ill try and get a pic of what im talking about
 
the overflow im speaking of was a single drain.... it wasnt overly loud sice inside the box the water flowed down the ramp and the air passed by the sides of the ramp...... ill try and get a pic of what im talking about
Yes please, a pic would help
 
Yes. Outside the tank you could put a tee instead of elbow. With small hole drilled into cap on topside of that tee, with airline going into small hole, and an air valve on that hose. You would have to adjust to find sweet spot, and if all tanks are fed by same return...
Drill second drain, be done, be safer
I don't really want to do a second drain on each tank. It would require a lot of reworking of what I have already done. Plus additional cost.

But I do like your idea of using a TEE. I might just do it this way.
 
Yup, i’m Familiar with glass holes.
Here’s a vid


Glass holes uses an elbow with air hose. I suggest using a tee to make it higher/safer, and a valve to control air to make it adjustable/quieter.
You could also use a street elbow inside the box turned upward. That would make water level inside box higher, so it doesn’t have as far to fall
 
Last edited:

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new