Icecap nano k1 skimmer not bubbling

  • Thread starter Thread starter Roliv081
  • Start date Start date
  • Tagged users Tagged users None

Roliv081

New Member
View Badges
Joined
Mar 30, 2023
Messages
17
Reaction score
1
Location
Broward county
What state or country do you live in
Florida
Rating - 0%
0   0   0
Hey y’all was wondering if anyone can help me out I just installed a skimmer into my reef tank and it’s not bubbling I put it all together and adjusted the skimmers flow correctly and it’s not bubbling. Am I missing something?

*** update I fix that issue and now I can’t stop it from overflowing no matter what direction I turn the knob and I’ve also adjusted the height bring it out of the water more and even submersing it more and it still over flows. Anybody thinks they can help let me know otherwise, I’m gonna return it.
 
Last edited:
Open the valve and lower the water level to just about the beginning of the neck curve, then slowly tune it in over the next few days little by little.
Yea it doesn’t t matter what I do it over flows
 
With wet bubbles? Maybe your sump water level is too high for it. Can you raise the skimmer on a piece of egg crate or something. Just don't create a dead spot of no water flow.
 
With wet bubbles? Maybe your sump water level is too high for it. Can you raise the skimmer on a piece of egg crate or something. Just don't create a dead spot of no water flow.
I’ve raised the skimmer so high
 

Attachments

  • IMG_4977.jpeg
    IMG_4977.jpeg
    141.3 KB · Views: 80
That might not be the best skimmer for you in your AIO. I made the assumption you had a below tank sump. And with the outflow butted up against the side of the chamber that flow might be impeded
 
I have one in an AIO. It's a beast. It pulls the driest filthiest skimmate.

It was a beeeeotch to break in though.

I had to mount it inside the display using the mounting magnet that way it would over flow into the tank. After 24 hours it calmed down and started pulling crud. But if OP's tank is new it's not going to break in for a long time. He needs wait until there is waste to skim if it is a new tank.

Edit:
Here is how I had it to get it started.
PXL_20230601_014848693.jpg
 
Last edited:
I have one in an AIO. It's a beast. It pulls the driest filthiest skimmate.

It was a beeeeotch to break in though.

I had to mount it inside the display using the mounting magnet that way it would over flow into the tank. After 24 hours it calmed down and started pulling crud. But if OP's tank is new it's not going to break in for a long time. He needs wait until there is waste to skim if it is a new tank.

Edit:
Here is how I had it to get it started.
PXL_20230601_014848693.jpg
I can’t put mine that deep in the tank or it will overflow. I literally Have to have it this high. I messed with it for hours yesterday. The directions say the bottom of the pump has to be 6-9 inches deep I can’t do that or it over flows. I also noticed it is putting air bubbles in the water Column not sure if it’s supposed to do that ethier
 

Attachments

  • image.jpg
    image.jpg
    210.2 KB · Views: 60
  • image.jpg
    image.jpg
    184.8 KB · Views: 65
  • image.jpg
    image.jpg
    125.4 KB · Views: 96
I can’t put mine that deep in the tank or it will overflow. I literally Have to have it this high. I messed with it for hours yesterday. The directions say the bottom of the pump has to be 6-9 inches deep I can’t do that or it over flows. I also noticed it is putting air bubbles in the water Column not sure if it’s supposed to do that ethier
How new is your tank? You can't get a skimmer to break in if your tank is clean/new.
 
I have the same one in my bc32.

Let it overflow back into the tank for a few days to break in, then try adjusting again. It needs to get dirtier to work.
 
How new is your tank? You can't get a skimmer to break in if your tank is clean/new.
Tanks of fine I’ve already dumped a full cup of brown coffee looking skimate. The problem is it is blowing bubbles into the tank now my entire sump area is bubbles
 
Tanks of fine I’ve already dumped a full cup of brown coffee looking skimate. The problem is it is blowing bubbles into the tank now my entire sump area is bubbles
It's a bubble machine for a while. Don't know what to tell you on that front.
 
Hey y’all was wondering if anyone can help me out I just installed a skimmer into my reef tank and it’s not bubbling I put it all together and adjusted the skimmers flow correctly and it’s not bubbling. Am I missing something?

*** update I fix that issue and now I can’t stop it from overflowing no matter what direction I turn the knob and I’ve also adjusted the height bring it out of the water more and even submersing it more and it still over flows. Anybody thinks they can help let me know otherwise, I’m gonna return it.
Update, it’s running great now! No more extra bubbles it ocasionally over flows and after a water change it takes a few hours to days to get back to normal
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new