Light recommendations needed. I’m picky about spectrums.

@Miami Reef as far as mounting just contact Daniel. But he has several 3D printed mounts for different size slotted aluminum. Believe he can and will do custom brackets also.
AA604AE5-BDFD-4038-B2C7-65EEF14DC224.jpeg
I was thinking of manually hanging each one with the wire hangers they come with.

What do you think? It’s in a canopy.
 
I was thinking of manually hanging each one with the wire hangers they come with.

What do you think? It’s in a canopy.
I only ever hanged 2 of them (over my sump and the QT).

In my case, with a single connection point (4 to 1) - I had struggled aligning it properly.
I assume this is because of both the rather short height (I looped each wire to make it half as long), as well as due to the small size of the fixture (longer distances are visually easier to align).

If you have 4 or at least 2 connection points, and using the full length of the wire, than I believe you should be fine.
 
Grouping is done automagically and you can separate them into different groups.
Each group keeps the lights in it in sync.
I was wondering how do you connect the lights it to the interface?

Is there WiFi or Bluetooth on the actual lights? How does the interface detect them? This topic has always interested me.
 
I was wondering how do you connect the lights it to the interface?

Is there WiFi or Bluetooth on the actual lights? How does the interface detect them? This topic has always interested me.
Oh, there is a reason why I said automagically earlier, I simply forgot to actually mention it :grinning-face-with-sweat:

The lights are using WiFi (hence the name - ReeFi - WiFi Controlled reef lights).

You power them on and than connect to one of the access points they launche (from your phone/computer)

From there, you browse into the IP address printed on the screen and follow the WiFi setup instructions.

Once a single light is configured and connected to your local network, you enter settings and click on the “scan new lights” option, which would automatically find new fixtures and configure them.

Once it’s done, all lights should be within the same group and synced.
 
One pro tip (I have 3 uno pros) is to set their ip addresses to static in your router. Otherwise when they reconnect it may re-assign a new ip and throw off the grouping.
 
One pro tip (I have 3 uno pros) is to set their ip addresses to static in your router. Otherwise when they reconnect it may re-assign a new ip and throw off the grouping.
True. Some routers will not preserve IP reservations and will need to be setup with static addresses.
 
I wish Reefi made a panel fixture of their build quality. I can’t handle that many cables and PSUs 😭
 
This got away from me I was going to post pretty much everything @DanyL posted. Thanks @DanyL saved me some typing and gathering. For the price point you can get 2 Reefi for 1 30 with better spectrum, control and power. I have 1 over my tank currently its 28x28x24" I am using the supplied 120 degree reflector and it covers that wall to wall but I do get shading, two would have fixed the issue I am sure or a bar of some sort. I am upgrading tanks to a 180 running 3 2.1s I will also probably get a helix or 2 to make sure I have coverage. The Reefi as already said have a great spectrum and are fully adjustable to whatever you like. The wifi is/was my biggest concern but the screen on the Reefi tells you what the address is so if for some reason it gets changed just type in the new one and you are good. This is with a single one running so not sure how that effects a group. But my single one does not lose its schedule when if the wifi address changes. Now if I could just figure out how to set a static address in my router I would be golden.
 
I was thinking of manually hanging each one with the wire hangers they come with.

What do you think? It’s in a canopy.
If he has a bracket I always prefer a solid mount. With hanging I feel they move around. But might work perfectly fine for you. Im very OCD
 
You can run 3 off this 1000 watt 36v ps...
https://www.jameco.com/z/HRPG-1000N...ng-Power-Supply-36V-28A-with-PFC_2358759.html
I'd consult people smarter than me though ..
Also adds $220- ish $'s to the build.
3.7 at 100% on all channels, yes.

But more realistically - you could easily fit 5-6 given that you won’t push them to their limits, but rather use that extra power to configure the channels the way you like.

That said, the PSU of the Uno 2.X Pro is 24v, the Uno 1 is 36v.

The only downside in doing so is that the length of the cable between the PSU to each of the fixtures must be roughly the same, and the wire gauge would need to be enormous (and pricy) to be rated for such huge loads.
 
I need help understanding how to hang a rail. I’m a bit confused.
 
Nicrew Gen 2 and make sure you actually like LEDs. Better than Radions at 25% the cost.

Giesemann V12 if you want a higher end, super polished looking fixture. When priced out, they’re actually a good deal

I wouldn’t touch Reefi, Orphek, Red Sea, Quanta, the new AI Hydra Edge, maybe a couple others I’m forgetting
I second the Nicrew. And honestly, I like that they cannot be controlled by an app. I'm a tinkerer, and lights are the last thing you want to change on a regular basis. I programmed the lights once...waited a bit, made some changes, and I haven't changed the settings since. I'm very happy with them.
 
I need help understanding how to hang a rail. I’m a bit confused.
I would vouch for a frame rather than a rail, it would be a lot easier to hang and align it.

As far as hanging goes - you can easily order modular aluminum profiles (2040/3030) with drilled and tapped holes, than simply attach a ring to it. Daniel already have adapters for them, so you could slide it right through the profile grooves.

Edit: technically you could also use T-Slot nuts (not the rotating ones) for this, but I would make sure to screw it all in so that the ring won’t easily slide in the groove.
 
Last edited:
Yes. Frame. 2040. That’s what he told me.

He’s been super helpful.
 
Last edited:
edit
 
Last edited:
View attachment 4114893


That metal tube has a button on top that you can press the release or raise the fixture.

The end of the wire is a ball that needs to go beneath the fixture. I can’t explain these things. Uch.


Don’t worry about it.
I have these laying around somewhere in my drawers.

From what I remember the ends are screwable - you could easily drill and tap the same thread in a profile, or use the equivalent T-Slot nut if you can find the correct threading (or get a smaller thread and tap it yourself).

But yeah, you could engineer it in many different ways.
 
IMG_0851.jpeg




How can I screw into the frame like this picture? Is that screw able the slide through the rail or is it stationary?

Don’t mind my simple minded questions. I’m not good at this kind of stuff.
 
IMG_0851.jpeg




How can I screw into the frame like this picture? Is that screw able the slide through the rail or is it stationary?

Don’t mind my simple minded questions. I’m not good at this kind of stuff.
Dont worry I am not either. I basically need someone to configure this for me and I would buy it and then I could figure out how to set it up. I have seen this before though the screw is in a block or small piece of metal that slides in the channel.
 

TOP 10 Trending Threads

WHAT KIND OF REEFING DEAL ARE YOU HOPING TO PICK UP THIS BLACK FRIDAY?

  • A whole new aquarium or complete system

    Votes: 2 11.1%
  • Lighting, pumps, or other major equipment

    Votes: 2 11.1%
  • Controllers, testing, dosing, or automation gear

    Votes: 2 11.1%
  • Dry goods and restocks, like salt, media, or food

    Votes: 2 11.1%
  • Corals! Must...Have...CORALS!!!

    Votes: 5 27.8%
  • Fish or other livestock

    Votes: 0 0.0%
  • Rock, sand, or other aquascaping supplies

    Votes: 1 5.6%
  • I’m browsing, but don’t have a specific target

    Votes: 2 11.1%
  • I’m not shopping for reef deals this year

    Votes: 1 5.6%
  • Other (Post in the comments)

    Votes: 1 5.6%
Back
Top
Home
Post thread…
Market
What's new