MP40 Mobius error

[CWalters]

Just added the RF chip to my MP40. I keep getting this error. Tried factory resetting etc. any other ideas?

 

[Sisterlimonpot]

Did you factory reset the driver?

 

[CWalters]

Did you factory reset the driver?

I held down mode and set until it flashed red white and blue, then mode until purple and red, and then power button until it reset.

Something else I need to do?

 

[Sisterlimonpot]

Try closing the app completely, power cycle the vortech and then try to push the update

 

[CWalters]

Try closing the app completely, power cycle the vortech and then try to push the update

Tried that. Tried turning on airplane mode as well. Super weird because when this chip was in my Vectra it works just fine

 

[Sisterlimonpot]

Ypu have it attached to mabius, so it's doubtful that the rf chip is the problem.

You're experiencing update issues.

Do you have an mxm connected to that mobius tank too?

 

[CWalters]

No. I don’t have Neptune. The board in the driver is brand new as well.

 

[Sisterlimonpot]

Try going to SETTINGS > TROUBLESHOOTING > VERIFY SETTINGS.

See what's corrupted with that VT

 

[CWalters]

Try going to SETTINGS > TROUBLESHOOTING > VERIFY SETTINGS.

See what's corrupted with that VT

Nothing will show up there though, I cannot get the MP40 to show in there.

 

[Sisterlimonpot]

Nothing will show up there though, I cannot get the MP40 to show in there.

Does it show up in DEVICES?

 

[CWalters]

No because it won’t let me add it until it updates. It shows up here though

 

[Sisterlimonpot]

Oh! My mistake, I thought you were beyond that.

That red icon on the top right indicates that the factory reset didn't take....


Can you do it again?

VorTech Propeller Pump Controller Reset

Overview EcoSmart and QuietDrive VorTech Controllers have 2 different resets available to you. To perform a soft or hard Reset, see their descriptions and instructions below.Soft Reset: Clears the...

support.ecotechmarine.com

 

[CWalters]

Oh! My mistake, I thought you were beyond that.

That red icon on the top right indicates that the factory reset didn't take....


Can you do it again?

VorTech Propeller Pump Controller Reset

Overview EcoSmart and QuietDrive VorTech Controllers have 2 different resets available to you. To perform a soft or hard Reset, see their descriptions and instructions below.Soft Reset: Clears the...

support.ecotechmarine.com

Tried reseting again and its still there

 

[Sisterlimonpot]

I'm only speculating here, I wonder if there's a conflict with that rf coming from a vectra.

I'm at a loss as well... you'll have to reach out to ecotech cs.

Completely closing the app or better yet restarting the phone/device, then factory reset the driver should've worked.

 

[CWalters]

I'm only speculating here, I wonder if there's a conflict with that rf coming from a vectra.

I'm at a loss as well... you'll have to reach out to ecotech cs.

Completely closing the app or better yet restarting the phone/device, then factory reset the driver should've worked.

Yea.. as soon as I thought about the vectra still showing up on Mobius without the chip, I deleted it. So not 100% sure what else...

 

[Sisterlimonpot]

Yea.. as soon as I thought about the vectra still showing up on Mobius without the chip, I deleted it. So not 100% sure what else...

Another long shot is to put the chip back in the vectra, go through the motions to remove it from mobius. And then factory reset the vectra.

Then put the rf chip in the vortech and see if that makes a difference?

 

[CWalters]

Another long shot is to put the chip back in the vectra, go through the motions to remove it from mobius. And then factory reset the vectra.

Then put the rf chip in the vortech and see if that makes a difference?

Nothing… thanks for the help. I will contact mobius Monday

 

[Sisterlimonpot]

Please reply back to let me know what the solution is

 

[CWalters]

Please reply back to let me know what the solution is

Will do. Going to pull a chip from one of my xr30s. See if it’ll update then swap it back.

 

[CWalters]

Alright… took the chip out of one of my xr30’s and instantly updated. Switched them back again and everything is working good!