Question about new DI canister.

  • Thread starter Thread starter kaceyo
  • Start date Start date
  • Tagged users Tagged users None

kaceyo

Active Member
View Badges
Joined
Aug 29, 2014
Messages
262
Reaction score
135
Location
Seattle
Rating - 0%
0   0   0
I'm setting up my new Home Depot RODI unit and noticed that the DI canister has what looks like a plastic cap insert at the end with the rubber seal. Do I need to remove it or is it permeated with tiny holes?
Also, I bought a flush kit with it and can't figure out how it works. It looks like It just allows the water to run through either one tube or two tubes, depending on the valve being open or shut. What's the deal?
Thanx,

Kacey
 
The plastic plug does have slots in it through which water could flow, but I cant get it to fit over the ring (fitting) in the canister head. The slots are on the sides of the cap so might be plugged up by the fitting once inserted.
 
Mind sharing pictures of the top of the di canister and the parts you are referring to? Typically you don't remove anything from this end and its put in with this end facing upwards.

As for your flush kit, this is exactly what it does. I'm guessing the kit did did not come with a flow restrictor but there will be one inserted into the RODI membrane housing. This will have to be removed and placed in the line that's not the one with the valve.

The way the flush works is when the valve is closed, it forces water through the flow restrictor which then forces water through the membrane at a certain ratio depending on how the flow restrictor is cut or which particular restrictor is place on the line. This in turn produces your RO water. When water is forced through the membrane particles will start to build up on the surface of the membrane. When you stop producing, if you don't have a flush kit, these particles will stay on the membranes surface and eventually begin to clog it prematurely or basically shortening its life. A flush kit works by providing a bypass for the restrictor giving you the ability to run higher flow over the surface of the membrane which will wash or "Flush" this particulate matter off of the surface. This has the benefit of delaying the surface build up from causing any performance issues of the membrane.
 
Mind sharing pictures of the top of the di canister and the parts you are referring to? Typically you don't remove anything from this end and its put in with this end facing upwards.

As for your flush kit, this is exactly what it does. I'm guessing the kit did did not come with a flow restrictor but there will be one inserted into the RODI membrane housing. This will have to be removed and placed in the line that's not the one with the valve.

The way the flush works is when the valve is closed, it forces water through the flow restrictor which then forces water through the membrane at a certain ratio depending on how the flow restrictor is cut or which particular restrictor is place on the line. This in turn produces your RO water. When water is forced through the membrane particles will start to build up on the surface of the membrane. When you stop producing, if you don't have a flush kit, these particles will stay on the membranes surface and eventually begin to clog it prematurely or basically shortening its life. A flush kit works by providing a bypass for the restrictor giving you the ability to run higher flow over the surface of the membrane which will wash or "Flush" this particulate matter off of the surface. This has the benefit of delaying the surface build up from causing any performance issues of the membrane.
Thanks Josh, I'll go ahead and set it up and flush the di cartridge out for a few minutes then.
 
Make sure you flush the carbon block separately BEFORE running any water through your RO membrane to flush the DI
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new