reef-pi :: An opensource reef tank controller based on Raspberry Pi.

[theatrus]

FYI - My probe gave roughly -150 for a 7.02.

I expect “around zero” to be fine for a 7.02 solution, so this number is fine.

There is a setting update I’ll fix in the driver where the gain of different Pico boards ends up set differently - some will report about -4000 and others -8000 (2x gain) for pH 10. It’s a quick software fix to lock all to 2x.

 

[Mikeneedsahobby]

Mine looked like it took the file, but the numbers in the UI look the same. I'm out and about, but I'll be home shortly.

I got mine working. It is giving a reading of 10.03 in my 10.02 calibration fluid. I closely followed your posts Dirt. so thank you. You and Ranjib helped me through this.

 

[Mikeneedsahobby]

I expect “around zero” to be fine for a 7.02 solution, so this number is fine.

There is a setting update I’ll fix in the driver where the gain of different Pico boards ends up set differently - some will report about -4000 and others -8000 (2x gain) for pH 10. It’s a quick software fix to lock all to 2x.

PH 10 was about -3,200 for me.

 

[DirtDiggler2823]

Man I feel for you, you are so close. But I can also see the issue with your commands. See , the last three commands in your screenshot is what matter, I can see your cookie and auth is correct as you can list the ph probes (against the pi 127.0.0.1), but in the calibration command you entered cookie file wrong, cookie.tst instead of cookie.txt. Just change that and you should be successful

Now I'm getting an error from the UI when I enable the pH probe "{"error":"stats for id: '1' not found"} | HTTP 404"

 

[DirtDiggler2823]

Man I feel for you, you are so close. But I can also see the issue with your commands. See , the last three commands in your screenshot is what matter, I can see your cookie and auth is correct as you can list the ph probes (against the pi 127.0.0.1), but in the calibration command you entered cookie file wrong, cookie.tst instead of cookie.txt. Just change that and you should be successful

yes, it is pico board.

Calibration is kicking my butt too right now. I think I am having the same issue as you, but I'm on day 1 instead of 7. I am carefully reading all your posts and @Ranjib 's responses to figure out what to do. I haven't given up yet. ... maybe soon.

I'm also baking peanut butter cookies and the raw dough is keeping my spirits up.

I got mine working. It is giving a reading of 10.03 in my 10.02 calibration fluid. I closely followed your posts Dirt. so thank you. You and Ranjib helped me through this.

My UI has not changed, and now I'm getting an error in my UI when I enable the probe. I've rebooted, and reloaded so far.

 

[DirtDiggler2823]

Nevermind. Got it! Thanks @Ranjib and @Mikeneedsahobby . I had to go back an undo a change I made in t he .json, but I finally got it.

 

[Bigtrout]

Just got my tp-link smart plug working with some prototype code . Its been a much desired thing that i want to support, and a couple of other folks were trying to get it done as well. So if you are want to try it out, with next version of reef-pi 3.x release you should be able to use these

Awesome!!!

 

[Ranjib]

Mine looked like it took the file, but the numbers in the UI look the same. I'm out and about, but I'll be home shortly.

If it took the file it means calibration will be applied. Enable the ph monitor after calibration. You should see a huge step function in the chart

 

[DirtDiggler2823]

Just got my tp-link smart plug working with some prototype code . Its been a much desired thing that i want to support, and a couple of other folks were trying to get it done as well. So if you are want to try it out, with next version of reef-pi 3.x release you should be able to use these

This is also quite exciting

 

[DirtDiggler2823]

If it took the file it means calibration will be applied. Enable the ph monitor after calibration. You should see a huge step function in the chart

It is reflecting an accurate pH now

 

[Ranjib]

As for the higher PH trend ive noticed that the KH guardian that is based off this same type of test states in there manual. That the machine must be 3 feet or less from the water and to not cut the tubing. So maybe it has something to do with the amount of tubing you have. Just a guess though. Im going to be following this I would love to build it. and try it out.

Welcome to reef2reef

 

[Ranjib]

ranjib have you put any thought into the sonar sensors for water height detection in sump? imo would be pretty nice because there are no parts in the saltwater to get salt creep on.

not yet. I am using the optical sensors, and pretty happy with it. @theatrus was talking about pressure based sensors, i have tinkered with e-tape based things in past as well. I am focused on clustering, calibration, ph based action, arbitrary pwm profile etc .. for the time being.

 

[trackerit]

It was very simple, the first step is to obtain the cookie. Txt, then see the id of the probe, place the probe im the solution ph10, and write the value, then place the probe im the solution ph7 and write the value, save the calibrste. Json file and execute the last command to send the calibrate. Json with the id of probe

 

[Ranjib]

It is reflecting an accurate pH now

W00t . If you want to get rid of the old readings , you can delete the current probe, recreate it again in disable state, apply calibration first and then enable it. Otherwise you wont see the daily ph swing in historic trends due to those high un-calibrated values (3000 in range).

 

[Ranjib]

It was very simple, the first step is to obtain the cookie. Txt, then see the id of the probe, place the probe im the solution ph10, and write the value, then place the probe im the solution ph7 and write the value, save the calibrste. Json file and execute the last command to send the calibrate. Json with the id of probe

Things will be lot easier once we have the UI ready.

 

[Ranjib]

It was very simple, the first step is to obtain the cookie. Txt, then see the id of the probe, place the probe im the solution ph10, and write the value, then place the probe im the solution ph7 and write the value, save the calibrste. Json file and execute the last command to send the calibrate. Json with the id of probe

But this is by no means a small feat, what we are seeing is an open hardware , opensoftware based ph system . how cool is that

 

[trackerit]

@Ranjib is it possible to make the current ph pnly have 2 decimals?

 

[DirtDiggler2823]

But this is by no means a small feat, what we are seeing is an open hardware , opensoftware based ph system . how cool is that

Pretty dang cool

 

[trackerit]

But this is by no means a small feat, what we are seeing is an open hardware , opensoftware based ph system . how cool is that

Lol, for me its amazing, picoboard, pihat, reefpi, i love it...

 

[DirtDiggler2823]

Lol, for me its amazing, picoboard, pihat, reefpi, i love it...

Nice to be part of something like this