Reefanatik 72x36x24 build

curious why the change ?
Man it’s been a while since I’ve logged on. I removed one MH to see how much difference it would make on temperature. It was getting to around 81f so just wanted to try it out…… plus I struggle allot whether I should just go all LEDs. LOL
 
Last edited:
Finally after over a year and a half I got my stand stained and coated. I’m happy with the results. Now I gotta install some LEDs and switches to turn lights on when I open the doors.
C8EDEBD6-1FDE-4905-BE02-746034545AFF.jpeg
C80D4BDA-00EE-470A-8441-2F1DC4237CF4.jpeg
73BA0B90-0570-43F9-824E-5E9FC6791C45.jpeg
 
Yea that chip won’t hurt the integrity of the tank. But upgrades are always fun so better hurry and do it before the tank blows!
 
Built a couple of shelves for my Redsea dosers and ran tubing through pvc pipes to hide them for a cleaner look. Will order grey 90s and tee’s and replace these temporary white ones so plumbing will match.
8B3D12BA-E8FE-4B47-96C9-87DF8F0F60E5.jpeg
C336B207-1739-4B67-B237-459D92F85D0B.jpeg
 
Well I’ve finally swapped to full Radion. I have ran Hamilton Radium 250W’s and Radion LED combo for years and finally transferred to full LED. Reason for the change….. Heat. I couldn’t run my MH’s for longer than 3.5 hours without display temp.getting hotter thean I’d like. A few months ago i installed a UV Sterilizer and it increased my temp. So now to try full Radion and see how it goes. I just ordered one more XR30. So i will have 8 XR15’s, 4 in the front, 4 in the back and 3 XR30’s In the middle. PAR numbers looked good throughout the tank except a little lower in the center of the tank. I think the 3rd XR30 should even the PAR out.
 

Attachments

  • 942E54A2-27F6-4111-A5B7-0B1BDCDC14AC.jpeg
    942E54A2-27F6-4111-A5B7-0B1BDCDC14AC.jpeg
    111.3 KB · Views: 149
  • E558B141-A745-4E0F-8139-861BDCEEF320.jpeg
    E558B141-A745-4E0F-8139-861BDCEEF320.jpeg
    188.2 KB · Views: 152
Built a couple of shelves for my Redsea dosers and ran tubing through pvc pipes to hide them for a cleaner look. Will order grey 90s and tee’s and replace these temporary white ones so plumbing will match.
8B3D12BA-E8FE-4B47-96C9-87DF8F0F60E5.jpeg
C336B207-1739-4B67-B237-459D92F85D0B.jpeg
Looks good. Going to steal that idea.
 
did you use any high density foam or anything between glass and plywood ? thinking about what i will need for my build . im thinking to either use marine ply or water resistant mdf under my tank only , sealed and coated .. for a cleaner look seeing that i may leave the stand exposed . but alot of people advise against it for tanks without the plastic trim at the bottom
 
did you use any high density foam or anything between glass and plywood ? thinking about what i will need for my build . im thinking to either use marine ply or water resistant mdf under my tank only , sealed and coated .. for a cleaner look seeing that i may leave the stand exposed . but alot of people advise against it for tanks without the plastic trim at the bottom
I installed the tank right above the 3/4" plywood, no foam or anything else.. see pg. 3.
 
I installed the tank right above the 3/4" plywood, no foam or anything else.. see pg. 3.
ok . i wanted to do something similar because i dont like the look of the foam as i may leave my stand bare .. i am guessing once the surface is truly flat it wouldnt cause an issue with the tank .
 
ok . i wanted to do something similar because i dont like the look of the foam as i may leave my stand bare .. i am guessing once the surface is truly flat it wouldnt cause an issue with the tank .
Honestly if i remember correctly, the manufacturer said to put plywood under my tank and not foam. i would deff. verify with manufacturer or do a lot more digging and see what is required/recommended for your tank.
 
Well I’ve finally swapped to full Radion. I have ran Hamilton Radium 250W’s and Radion LED combo for years and finally transferred to full LED. Reason for the change….. Heat. I couldn’t run my MH’s for longer than 3.5 hours without display temp.getting hotter thean I’d like. A few months ago i installed a UV Sterilizer and it increased my temp. So now to try full Radion and see how it goes. I just ordered one more XR30. So i will have 8 XR15’s, 4 in the front, 4 in the back and 3 XR30’s In the middle. PAR numbers looked good throughout the tank except a little lower in the center of the tank. I think the 3rd XR30 should even the PAR out.
I have a 72x36x20. Are those MP40s or 60s?

And does the other end of the tank have the same flow setup?
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 10 41.7%
  • I’d trust someone who knows my tank to choose

    Votes: 0 0.0%
  • I’d rather get a gift card and pick it myself

    Votes: 9 37.5%
  • I’d prefer gear or supplies instead

    Votes: 0 0.0%
  • Please don’t surprise me with livestock

    Votes: 5 20.8%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new