RODI Flush Valve Leaking

  • Thread starter Thread starter mjszos
  • Start date Start date
  • Tagged users Tagged users None

mjszos

Valuable Member
View Badges
Joined
Sep 7, 2021
Messages
1,850
Reaction score
6,628
Location
Chicago, IL
What state or country do you live in
Illinois
Rating - 0%
0   0   0
Hey all,

I have a BRS 75 GPD 5 Stage Premium Plus RODI system that I’m running, but recently noticed that the flush valve has a slight leak. I’ve tried tightening all of the fittings, lowering PSI, checking membranes, etc. it’s been used for less than 6 months and has produced a maximum of 100-125 Gallons (membranes aren’t even changing colors it’s so fresh).

wondering if anyone has seen this before and resolved it. Thankfully I can keep a towel on it and a bucket below while I produce water, but obviously that’s not a long term solution.

Cheers and thanks!

-M

A61466B7-40E3-4077-99D3-AE3297174D32.jpeg
 
Yup and yup. Your local home improvement center should have a valve that will work to replacethe leaking one. I guess the leaking valve is repairable but it seems like a lot more work than just rpelacing it.
 
Yup and yup. Your local home improvement center should have a valve that will work to replacethe leaking one. I guess the leaking valve is repairable but it seems like a lot more work than just rpelacing it.

that is also your flow valve, that is matched to membrane gpd. so you need to get the same one

This is what I figured. If I pickup a valve for it, I presume I’ll want to make sure it’s rated for the 75GPD that my system is - correct? Or would I get something that supports X PSI of flow?
 
As stated in post #4, yours is a combo flush valve AND flow restrictor so seems easiest to just buy the same/right one from BRS.

You could get any valve and add a separate flow restrictor but I think you'd have to plumb it differently (split the lines) which may be desired but not as easy.
...unless I'm just being dumb
 
Hey all,

I have a BRS 75 GPD 5 Stage Premium Plus RODI system that I’m running, but recently noticed that the flush valve has a slight leak. I’ve tried tightening all of the fittings, lowering PSI, checking membranes, etc. it’s been used for less than 6 months and has produced a maximum of 100-125 Gallons (membranes aren’t even changing colors it’s so fresh).

wondering if anyone has seen this before and resolved it. Thankfully I can keep a towel on it and a bucket below while I produce water, but obviously that’s not a long term solution.

Cheers and thanks!

-M

A61466B7-40E3-4077-99D3-AE3297174D32.jpeg
@mjszos , when you flush the system do you have water comes out also from the blue line ?
 
@mjszos , when you flush the system do you have water comes out also from the blue line ?

A trickle.

This is resolved now though, I sent an email to BRS support on it with some information and they ended up just shipping one out to me priority - cut the tubes and installed the new one and everything is good to go!
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 17.7%
  • Fish or coral food

    Votes: 5 5.2%
  • Test kits or reagents

    Votes: 10 10.4%
  • Filter media or replacement fleece

    Votes: 5 5.2%
  • RO/DI filters or supplies

    Votes: 15 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 12 12.5%
  • I keep a backup of everything

    Votes: 25 26.0%
  • Other (Post in the comments)

    Votes: 7 7.3%
Back
Top
Home
Post thread…
Market
What's new