Tank overheating

  • Thread starter Thread starter StacyW
  • Start date Start date
  • Tagged users Tagged users None

StacyW

New Member
View Badges
Joined
Aug 28, 2019
Messages
21
Reaction score
5
What state or country do you live in
United Kingdom
Rating - 0%
0   0   0
For the last five days, my tank has been overheating according to a inkbird 306T. The inkbird and two heaters were new and were holding a constant heat previously. Firstly, it was noticed that the temperature had risen from 25.2 to 26.4 so the heaters were switched off to remove them from the equation. The temperature remained stable at 26.4. In the mean-time, the temperature has again risen to 27.2.


Up to now, the UV & its pump have been switched off just to remove them from the equation too. This leaves only the return pump, a Jeabo in the sump and a Tunze 6040 running in tank, both devices appear to be functioning correctly.

The LED lighting appears to have no effect on the tank temperature.

What can be making the tank heat up?
 
double check the location of the inkbird probe.

it may be too close to a heat generating piece of equipment. - or in my case of a what the ... , not in the tank ;Facepalm
 
The probe was the first thing to be checked, it is secured by the dubious sucker and is located away from the return pump.
 
Also consider the temperature in the room.. has this changed recently? What is your ambient air temp?
 
Double check your tank temp with a calibrated or trusted thermometer. The inkbird may have drifted from calibration.
The temperture is virtually correct as it was checked by a fluke ir thermometer.
 
Also consider the temperature in the room.. has this changed recently? What is your ambient air temp?
The room temp is around 22 degrees C.
 
Have you shot the return pump with the IR?
Hello, after aiming the gun directly at the water above the return pump, that gives a 1 degree rise in temp so this might be the culprit! The sump seems to be one degree higher than the DT.

There is a spare return pump here which can be fitted, which i believe to be the next move. Also, i have turned of the protein skimmer, just in case.
 
Hello, after aiming the gun directly at the water above the return pump, that gives a 1 degree rise in temp so this might be the culprit! The sump seems to be one degree higher than the DT.

There is a spare return pump here which can be fitted, which i believe to be the next move. Also, i have turned of the protein skimmer, just in case.

Sounds like you may have found the issue.
 
I stopped using the Inkbird temp controllers because they kept losing calibration. After they were 4-5 months old I would notice the temp would keep creeping up and I would recalibrate but kept having to adjust the offset to get them to read right. Ultimately reaching the limit of the adjustment. I switched to the Bayite controller and have not had an issue since. I check it for accuracy once a month and so far in the past 8 months I have not had to recalibrate it yet. The Inkbird controllers I was having to recalibrate every two weeks.

bayite Temperature Controller BTC201

The Bayite also is accurate to 2/10 of a degree F. So if you want it to cut power to the heater at 77.2, it will.
 
Last edited:
I stopped using the Inkbird temp controllers because they kept losing calibration. After they were 4-5 months old I would notice the temp would keep creeping up and I would recalibrate but kept having to adjust the offset to get them to read right. Ultimately reaching the limit of the adjustment. I switched to the Bayite controller and have not had an issue since. I check it for accuracy once a month and so far in the past 8 months I have not had to recalibrate it yet. The Inkbird controllers I was having to recalibrate every two weeks.

bayite Temperature Controller BTC201

The Bayite also is accurate to 2/10 of a degree F. So if you want it to cut power to the heater at 77.2, it will.
Unfortunately, this controller is not available in the UK but, thanks.

For the last day, the temperature has slowly dropped to 26.6.............

For now, untill a new pump is bought, this temperature is acceptable. However, I still can not understand where the extra heat is coming from in the sump.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 19 27.9%
  • I’d trust someone who knows my tank to choose

    Votes: 2 2.9%
  • I’d rather get a gift card and pick it myself

    Votes: 26 38.2%
  • I’d prefer gear or supplies instead

    Votes: 2 2.9%
  • Please don’t surprise me with livestock

    Votes: 19 27.9%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new