Tank reseal Input on bubble

  • Thread starter Thread starter Blindface
  • Start date Start date
  • Tagged users Tagged users None

Blindface

Community Member
View Badges
Joined
May 12, 2019
Messages
47
Reaction score
24
What state or country do you live in
New York
Rating - 0%
0   0   0
hey if anyone could give there input that would be amazing!
I just resealed a used tank that I got and was wondering if I should be worrying about these two tiny bubbles ?
It’s a 80 gallon lagoon.
I’m really hoping you all say not to worry .

IMG_8277.jpeg IMG_8276.jpeg
 
I wouldnt since its in the interior corner seal if it was between the glass panes then yes most likely would be an issue. this could flake off when scrubbing the tank.
 
What thickness did you do inbetween the panes where they but up i dont see any black silicone inbetween there or what kind of reseal did you do?
 
What thickness did you do inbetween the panes where they but up i dont see any black silicone inbetween there or what kind of reseal did you do?
Hey thanks for the reply, it’s just shy of half an inch on each side. It was originally sealed with black silicone before I bought it.
 
Hey thanks for the reply, it’s just shy of half an inch on each side. It was originally sealed with black silicone before I bought it.
So is the silicone clear inbetween the 2 where they meet in the corner? Normally there is silicone that needs to be inbetween that section. As long as there is no bubbles inbetween there you should be good
 
When you resealed the tank, did you make sure to completely disassemble the entire tank and remove all of the original silicone?
 
When you resealed the tank, did you make sure to completely disassemble the entire tank and remove all of the original silicone?
What do you mean disassemble? Like remove the silicone that is between the glass? No, I just removed the silicone on the edge. But I did clean it well, after using a razor blade to remove the silicone with some acetone. I was real thorough.
 
So is the silicone clear inbetween the 2 where they meet in the corner? Normally there is silicone that needs to be inbetween that section. As long as there is no bubbles inbetween there you should be good
I think it’s more so just that the pane of glass was sealed so close together before of the bottom “rim”, that it’s an extremely thin layer. Just my speculation. But on the outside of the tank you can see the original black silicone still on the corner, so it’s definitely black
 
What do you mean disassemble? Like remove the silicone that is between the glass? No, I just removed the silicone on the edge. But I did clean it well, after using a razor blade to remove the silicone with some acetone. I was real thorough.
To reseal a tank correctly you have to completely take the entire tank apart, remove ALL of the old silicone from the glass panes and redo ALL of the seals as you put it back together. If you don't, you are asking for a leak.
 
New silicone does not adhere to old silicone which is why it ALL must be removed before resealing a tank. The tank size doesn't matter in regards to that.
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new