The brace on my 40 breeder is cracking!

  • Thread starter Thread starter Ds04384
  • Start date Start date
  • Tagged users Tagged users None

Ds04384

Active Member
View Badges
Joined
Dec 13, 2015
Messages
401
Reaction score
270
Rating - 0%
0   0   0
I walked past my tank and noticed a line on the center of my top rim. I went to wipe it off and found that the line was actually light passing through a hairline crack? It goes up the front of the rim and hals
 
I walked past my tank and noticed a line on the center of my top rim. I went to wipe it off and found that the line was actually light passing through a hairline crack? It goes up the front of the rim and hals

I know it may be hard to capture in a picture, but a picture may be helpful for advice.

#reefsquad
 
Here’s a video, hopefully you can see it
 

Attachments

  • 271DDB26-A2A6-47CC-B4A0-811746BD021D.MOV
    19.4 MB
I’m not sure if that video worked or not. Here’s a picture

5A0A7F92-271C-4CE1-85CB-1D4A39BC9C96.jpeg
 
You have a few options.
1. Do nothing and watch to see if you enlarges
2. Try to patch with silicone and adhesive
3. Replace brace
4. Replace the tank, with $1/gallon sale it would run you $40 for a new one

I would probably do option #4, this size tank is inexpensive.
 
This may vary by area, my local Petco has them for $40 during the sale. Even $50 isn't bad, will probably cost you at least that to try to replace the brace, and would involve draining the tank.
 
I agree with the above, replace the tank. Better to be safe. If it had a center brace i'd say you could probably get away with it, but those tanks didn't have a center support and were known to bow out slightly when filled.
 
I've never seen one cracked that way. Usually, it is the cross brace that separates from the edge.

I think you should monitor. I'd also cut a strip of plastic to the correct length and width to glue on. Clamp on to the front until it sets. Remove the clamps.

I look at the picture and feel like it isn't something where failure is imminent, but should be addressed sooner rather than later.
 
One extra bit of info is that the back of the tank is covered in a rock wall that is covered in montis and zoas so if I went the route of replacing the tank I would be sacrificing that
 
One extra bit of info is that the back of the tank is covered in a rock wall that is covered in montis and zoas so if I went the route of replacing the tank I would be sacrificing that

What's the alternative? A tank failure and thousands of dollars in damage?
 
What's the alternative? A tank failure and thousands of dollars in damage?
Well it looks like the rim can be replaced and I can get a new one with a center brace. It might end up being around the same as a new tank but this way I won’t have to drill and new one and I can keep my rock wall.
 
Well it looks like the rim can be replaced and I can get a new one with a center brace. It might end up being around the same as a new tank but this way I won’t have to drill and new one and I can keep my rock wall.

I am not sure if you have replaced a brace before, but it does take some work and ideally the tank should be drained until the new silicone cures. When you start removing the first piece you have to apply a decent amount of force, it feels like you may break the glass. As you start cutting the old silicone and adhesive a lot of debris will get into your tank. Either way, good luck.
 
I have tried cutting siliconed pieces out before too. Nearly impossible. I think the most viable next step is to whip out mr Visa and buy a 120 gallon drilled.... you have a perfect excuse.
 
I am not sure if you have replaced a brace before, but it does take some work and ideally the tank should be drained until the new silicone cures. When you start removing the first piece you have to apply a decent amount of force, it feels like you may break the glass. As you start cutting the old silicone and adhesive a lot of debris will get into your tank. Either way, good luck.
So I was hoping to drain the tank more like half way and leave it that way for at least several hours but I figured it wouldn’t be as crucial to leave it that way until it is fully cured since the silicone in this situation seems more about holding the brace in the right spot rather than actually adding any support. As long as the brace is firmly on top of the tank then it shouldn’t matter too much if there is some water in the tank right? I could be very off but that was my assumption since it’s not like silicons holding the glass together
 
The main issue with that is that first you’re going to have a hard time pulling off the other brace. And then when it’s off the glass will bow more with the water. Then you’ll have to get the new brace on there with bowing glass. It can be done if you’re careful but please don’t get hurt. I had a friend doing something similar get sliced up nicely because the tank had a bow and when he tried to get the new brace on it busted the tank.
 

TOP 10 Trending Threads

WHAT KIND OF REEFING DEAL ARE YOU HOPING TO PICK UP THIS BLACK FRIDAY?

  • A whole new aquarium or complete system

    Votes: 3 12.0%
  • Lighting, pumps, or other major equipment

    Votes: 4 16.0%
  • Controllers, testing, dosing, or automation gear

    Votes: 2 8.0%
  • Dry goods and restocks, like salt, media, or food

    Votes: 2 8.0%
  • Corals! Must...Have...CORALS!!!

    Votes: 6 24.0%
  • Fish or other livestock

    Votes: 1 4.0%
  • Rock, sand, or other aquascaping supplies

    Votes: 1 4.0%
  • I’m browsing, but don’t have a specific target

    Votes: 4 16.0%
  • I’m not shopping for reef deals this year

    Votes: 1 4.0%
  • Other (Post in the comments)

    Votes: 1 4.0%
Back
Top
Home
Post thread…
Market
What's new