UV sterilizer plumbing

  • Thread starter Thread starter DmitryB
  • Start date Start date
  • Tagged users Tagged users None
I'm also have a little trouble trying to picture what you're trying to do, and I don't want to guess the wrong configuration. Would you be able to draw it out a little bit?

In general, yes it sounds like a reducer bushing is what you're looking for:

1787424240456.png


These would slide into a PVC fitting like a pipe would. You can get various configurations of sizes, with options for slip or thread for either connection. There are reducer couplings too (which go over PVC pipe) but it sounds like a bushing is better for you, if I'm picturing things correctly.

The way you'd switch from PVC to vinyl tubing is with a barb adapter:

1787424445581.png


These are also offered with various configurations of thread and barb size, and you can get ones with male and female threads. So if I were going from, say, a 1.5" PVC fitting to 3/4" vinyl tube, I'd look for a 1.5" x 3/4" FNPT reducer bushing (i.e. with the 3/4" hole being threaded). The other side can be slip or thread depending on what you're connecting to. Then I'd just need a 3/4" MNPT x 3/4" barb adapter, which is an easy size to find. The barb adapter should be plastic (the brass ones will rust and they can kill invertebrates).

Use teflon tape on the threaded connections, but if you haven't used if before be sure not to use too much. The added pressure can split fittings in some cases.

Also, you'll need a hose clamp to make sure the hose stays on the barb. Stainless steel (if it will be dry) or plastic (if it will get wet) are both options. I feel like the metal ones do a better job, but even stainless steel will eventually rust in seawater, so sometimes I go for plastic. I always go for plastic if it will be submerged.
I'm not explaining it well because I don't know plumbing so I'm more like "Can this doohickey go on that doohickey and work?"

I'm working on another diagram that will hopefully be clearer than I am! All the photos above are great, exactly what I need. One thing I hope I can make is True Union Ball Valve that is also a reducer, so I can skip an extra step of plumbing.

And I'm STILL trying to determine where the actual UV unit will go. There is just so little space in the stand that it's frustrating. I've figured out a way to hang it above, but it's still so tight with the skimmer sticking out of the sump. It will absolutely be in the way of doing anything inside the stand. So... I was trying to avoid placing it behind the stand - there is just enough room to fit a UV there, between the stand and the wall. But it will clear a lot of space in the stand, so I think that's where it will go. Now I just need to decide if it will stand on the floor back there or if I can elevate it to be at the top-of-sump level, so there is a bit less plumbing. I'd need to make some sort of platform for it to sit on...

Thank you guys! A new diagram is coming soon! (By 2028 I should have it all figured out.) I'd love to finally connect it. I put a UV on my 40 gallon (drop in UV for an AIO) and the water cleared up so beautifully that I'm looking at this 170 and going "Grrrr."
 
Ok so.... there is FINALLY some progress on my part. I've been building and rebuilding the plumbing for this a few times. This is what I've finally come up with. I will run a separate pump for the UV unit. Running a separate pump solves a lot of plumbing issues. And there just isn't enough space in the stand there to do everything. So the photo is for the set-up I've settled on. I just cemented that section in. (HOW LONG BEFORE I CAN TURN THE RETURN PUMP BACK ON???) The empty connection at this moment is where the return UV will be.

Tell me this will work because otherwise I quit! LOL

IMG_8352.jpg
 
Ok so.... The plumbing is done, the water is flowing. I ended up (at least for now) setting up a separate pump for the UV because it saves a lot of plumbing questions. One thing I did not think through was that the two different pumps have different flows, which means the overflow is now kind of a mess - and I certainly don't want to start adjusting the drain valve each time I switch between the two. So here's what happening.

Normally I'm running the MightyJet XL (2656 gph) at 50%. The UV is a Lifegard Quiet One 1188 gph. Theoretically my MightyJet is running at (roughly) 1,328 gph and the drain is adjusted to that. To have something in the same ballpark I'd have to run the UV pump at 100%/1188gph. But when I did, the overflow box filled up and the drain has far more water going through it than it does at 1,328. Is this making any sense? So I lowered the QuietOne down to setting 5 - which is FAR FAR lower and while the overflow is ok, but drain has far more water coming down. Doesn't this mean that the water is being recirculated much faster, which is causing this "backup?" But as far as GPH go, it is currently just a fraction of what MightyJet normally does. I'm very confused. (Is any of this making sense??)

IMG_8382.jpg
 
I certainly don't want to start adjusting the drain valve each time I switch between the two. So here's what happening.
So, you’re going to need to adjust the drain valve with your configuration… any time you add or remove appreciable return flow, you’re going to need to re-tune the primary drain to a full siphon to mitigate noise! (Aquariums normally don’t change in return flow much, or regularly, so the average reefer leaves this valve untouched for months once dialed in!)

Furthermore, as I discussed in great detail prior, the plumbing both of these pumps share is only 3/4”, so I’d be amazed if you’re getting much more than 800GPH of actual observed return flow, after massive frictional losses from the plumbing…

This said, you’d be better off running this UV directly inline on the return pump, meaning its flow remains constant, and you aren’t turning most of the consumed electricity into heat trying to make two oversized pumps fight to push water through one undersized return plumbing line!
 
I certainly don't want to start adjusting the drain valve each time I switch between the two. So here's what happening.
So, you’re going to need to adjust the drain valve with your configuration… any time you add or remove appreciable return flow, you’re going to need to re-tune the primary drain to a full siphon to mitigate noise! (Aquariums normally don’t change in return flow much, or regularly, so the average reefer leaves this valve untouched for months once dialed in!)

Furthermore, as I discussed in great detail prior, the plumbing both of these pumps share is only 3/4”, so I’d be amazed if you’re getting much more than 800GPH of actual observed return flow, after massive frictional losses from the plumbing…

This said, you’d be better off running this UV directly inline on the return pump, meaning its flow remains constant, and you aren’t turning most of the consumed electricity into heat trying to make two oversized pumps fight to push water through one undersized return plumbing line!
I'm not running both pumps at the same time. It's one or the other. Connecting regular return and UV to the same pump - but to have option to run UV or shut it off - is tricky with such limited space in the stand. I will try to figure out a way to do that later, but wanted to get the UV running after all this time.

I guess one option is to just run the UV with the light off when desired, but that would mean shutting off the return during UV servicing. Also, wouldn't running water through that continuously dirty it inside? So next step will be to find a way to run both from same pump.
 
I guess one option is to just run the UV with the light off when desired, but that would mean shutting off the return during UV servicing. Also, wouldn't running water through that continuously dirty it inside?
Yes, and yes… unless you plumb bypass circuit, as discussed prior!

From what I understand, best/bet with a traditional UV sterilizer is actually running it 24/7, as each startup cycle negatively impacts bulb lifespan!


So, a perfect world would be:

— plumb it to the return, with a bypass circuit for service as a continuously operating piece of equipment…

— or, a dedicated sump to sump/display to display arrangement for periodic use…
 
I guess one option is to just run the UV with the light off when desired, but that would mean shutting off the return during UV servicing. Also, wouldn't running water through that continuously dirty it inside?
Yes, and yes… unless you plumb bypass circuit, as discussed prior!

From what I understand, best/bet with a traditional UV sterilizer is actually running it 24/7, as each startup cycle negatively impacts bulb lifespan!


So, a perfect world would be:

— plumb it to the return, with a bypass circuit for service as a continuously operating piece of equipment…

— or, a dedicated sump to sump/display to display arrangement for periodic use…
I haven't heard about lifespan of the bulb being affected by shutting on/off. Is that shutting off the bulb or just the flow through the unit? (I know that, for example, we were always told that Mac computers and their hard drives were better off running continuously.)
 
Is that shutting off the bulb or just the flow through the unit?
The bulb specifically, each time it’s fired up

Flow just needs to be going through the UV any time it’s turned on, or it will overheat!
 
Is that shutting off the bulb or just the flow through the unit?
The bulb specifically, each time it’s fired up

Flow just needs to be going through the UV any time it’s turned on, or it will overheat!
Interesting about shutting bulb on/off. I was rather hoping to not run it at night when pods are more active to keep them from getting zapped!
 
Interesting about shutting bulb on/off. I was rather hoping to not run it at night when pods are more active to keep them from getting zapped!
You can run your UV this way, it just marginally decreases bulb life!
 
Interesting about shutting bulb on/off. I was rather hoping to not run it at night when pods are more active to keep them from getting zapped!
Interesting I have an aqua uv 114watt running in my 60 gallon , from what I’ve heard is the best time to use uv was at night. Well from an hr before lights out and about 2 hrs after lights on. It’s when spores usually come out “ ich” is what I’m referring too. My flow rate is about 700gph running one lamp on 24/7 and the other lamp turning on as stated above.

I don’t think you need to worry about zapping any of your pods or Amphipods I’ve been running this set up for 4 months now and I have plenty of pods and amphipods in the sump and display tank.

I would just run the uv pump 24/7 adjust overflow to it and have the other pump as back up. You can turn off and on to your set schedule might be easier that way.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 24.5%
  • I’d trust someone who knows my tank to choose

    Votes: 9 8.5%
  • I’d rather get a gift card and pick it myself

    Votes: 43 40.6%
  • I’d prefer gear or supplies instead

    Votes: 2 1.9%
  • Please don’t surprise me with livestock

    Votes: 26 24.5%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new