ACIII help

[gflat65]

I've been posting this anywhere I can think of to find some insight. I am trying to update my ACIII with new timers and code. When I click Update, it starts to update, but then hangs. It has been updating now for over an hour and I have 5 bars on the status bar... I get a message at the bottom that says 'Waiting for {IP addy}/cgi-bin/program.cgi...' I don;t have any errors on the code (I worked through those). I originally had 27 timers, and it was truncating 3 of them (then I found the one place in all those I've searched that told me the max timers for the ACIII-I will likely need an ACIII Pro to get more timers...). I corrected the code issues, but still can't get it to finish the update. I've tried two separate computers and get the same result. Any ideas?

Here is the code

MH1$-A01
MH2$-A02
MH3$-A03
VH1$-A04
HT1%-A05
SP1#-A06
MH4$-A07
VH2$-A09
HT2%-A10
SP2#-A11
CHL%-A12
CR1#-B01
CR2#-B02
CR3#-B03
C02#-B04
RP1#-B05
RP2#-B06
ML1$-B07
CHP#-B08
T51$-B09
T52$-B10
T53$-B11
CAP&-B12
CR4#-B13


If Sun -120/120 Then VH1 ON
If Sun -120/120 Then VH2 ON
If Sun -030/030 Then MH1 ON
If Sun -030/030 Then MH2 ON
If Sun -030/030 Then MH3 ON
If Sun -030/030 Then MH4 ON
If Moon 000/000 Then ML1 ON
If Timer VH1 = ON Then ML1 OFF
If Sun -120/120 Then T52 ON
If Sun -030/030 Then T51 ON
If Sun -030/030 Then T53 ON
If Temp > 83.4 Then MH1 OFF
Max Change 020 M Then MH1 ON
If Temp > 83.2 Then MH2 OFF
Max Change 020 M Then MH2 ON
If Temp > 83.4 Then MH3 OFF
Max Change 020 M Then MH3 ON
If Temp < 77.0 Then HT1 ON
If Temp > 77.5 Then HT1 OFF
If Time > 00:00 Then SP1 ON
If Temp > 83.0 Then SP1 OFF
If Temp < 77.0 Then HT2 ON
If Temp > 77.5 Then HT2 OFF
If Time > 00:00 Then SP2 ON
If Temp > 83.0 Then SP2 OFF
If Temp > 81.0 Then CHL ON
If Temp < 80.0 Then CHL OFF
If Time > 00:00 Then CR1 ON
If Time > 00:00 Then CR2 ON
If Time > 00:00 Then CR3 ON
If Time > 00:00 Then CO2 ON
If pH < 07.90 Then CO2 OFF
If Time > 00:00 Then RP1 ON
If Time > 00:00 Then RP2 ON
If Time > 00:00 Then CHP ON
If Time > 00:00 Then CAP ON
If FeedA 000 Then CR1 OFF
If FeedA 000 Then CR2 OFF
If FeedA 000 Then CR3 OFF
If FeedA 000 Then RP1 OFF
If FeedA 000 Then RP2 OFF
If FeedB 000 Then CR4 OFF

 

[gflat65]

Think I got it mostly working now... Neptune has contacted me and is working through the last little issues with me now.

 

[bkv1997]

I'd be interested in the outcome if you don't mind sharing...

 

[gflat65]

I had to load the new additions slowly. If I tried feeding it everything at once, it choked... I loaded a few timer names, updated, the associated code, updated, more timers, more code, etc. It finally took it all. I downloaded the newest firmware this morning and the lastest edition of Aqua notes this morning, so I'll work on updating everything to see if that speeds up transfers. I am still having an issue with control over the last DC8, but was told by Curt at Neptune that if it is a 4 wire phone cord, it should work. I'm going to dig in and see what I can figure out. All the important stuff is running now, though. I was frantic there for a little while because I had rewired everytign to the DC's trying to get everythign ready for a quick switch to the generatior if Gustav turned this way, then couldn't get any controls, so I had to rewire last minute before bed that night. Not pleasant sounds emanating from the Flatness household that night;).