Fatmike's Sexy 57 Rimless

For your return get some double sided sticky tape and something that had a hole in it and zip tie it to the back of the tank to hold it in place. " like one of your extras from your mp10
 
For your return get some double sided sticky tape and something that had a hole in it and zip tie it to the back of the tank to hold it in place. " like one of your extras from your mp10

Ha thanks for that! ive been trying to figure out how the heck I was going to keep it in place
 
So I dont like how far out the drain goes from the bulkhead on the inside of the tank. the bulkhead I have is a completely threaded bulkhead and not a slip threaded like I would of liked to have. but at least now I know what works best after 4 or 5 different plumbing attempts lol

so I ordered a Male threaded x slip 90 degree elbow online so I can get the drain closer to the back wall. then hopefully I will be satisfied!
 
Mike look at my DIY trust me with alot of gravity feed lines you get a ton of bubbles ill take a video to show how good it works. I have a cap on the bottom of the pipe. It's a 4" but you can do the same with a 3" or 2"
 
Ya I saw that. It's a very nice idea! I'm thinking I won't have a problem with bubbles. But if and when I do I'll definitely do something like that!
 
The best part about it is if you cap the bottom all the junk collects in the tube and all you do is remove the pipe and clean out the tube and not your whole sump.
image.jpg
 
ok now you have really caught my attention... lol

I was going to use socks but they are so annoying
 
ok now you have really caught my attention... lol

I was going to use socks but they are so annoying
I hate socks!! Only time I use them is when I do my monthly cleaning I take my turkey baser and spray out all the rocks and use my sock till the water is clear and repeat.
 
And your just going to have that in the corner of your sump where the water drains down correct?
 
Dang I need my sump! Then i can measure it out. In going to do this I believe. I'm going to send you a pm tomorrow to get some details
 
Definitively looking into this. Its like a mini settling tank which is exactly what I was trying to figure out how to build

Sent from my HTC6435LVW using Xparent Skyblue Tapatalk 2
 
Yep thanks for that chadder!

So I am defintely going to be doing what chadder has done. it should work pretty well!

and today I ordered a bucket of Red Sea Coral Pro salt!
 
Alright I was bored so I taped out where everything is going

small box to the left is the ATO box
C1229444-ADFD-4731-A458-1B74BE7ECFD1-756-000000C1E49B2589_zpsf37ca154.jpg


I also heard from atomic reef the sump and ato box should be shipped by the end of the week!
 
Last edited:
Have you used the Red Sea salt before? I've had issues from it in the past.

No never I was researching it today and I couldnt find one bad thing about it. I should of posted up on here to see if anyone had any problems with it

what probalems did you have
 

TOP 10 Trending Threads

WHICH PART OF YOUR SETUP IS HARDEST TO REACH OR REMOVE FOR ROUTINE MAINTENANCE?

  • Glass behind or beside the tank

    Votes: 11 22.0%
  • Powerheads or wavemakers

    Votes: 4 8.0%
  • Sump or rear filtration chambers

    Votes: 7 14.0%
  • Skimmer or other filtration equipment

    Votes: 6 12.0%
  • Overflow or plumbing

    Votes: 10 20.0%
  • Lights or lids

    Votes: 0 0.0%
  • Mine is pretty easy to access!

    Votes: 11 22.0%
  • Other—tell us what I missed

    Votes: 1 2.0%
Back
Top
Home
Post thread…
Market
What's new