Orphek OR2 blue bar broken??

[bullseyereef]

I have two 48" Orphek OR2 blue bars over my tank, one of my bars only half is working. Anyone else ever experience this? is there a fix or does it need to be replaced. I've tried to reach out to Customer service twice with no response. Any help would be great thanks.

 

[vetteguy53081]

I have two 48" Orphek OR2 blue bars over my tank, one of my bars only half is working. Anyone else ever experience this? is there a fix or does it need to be replaced. I've tried to reach out to Customer service twice with no response. Any help would be great thanks.

I had the same
CS reached out to me and offered a very discounted price on a OR3 replacement

 

[oreo54]

I have two 48" Orphek OR2 blue bars over my tank, one of my bars only half is working. Anyone else ever experience this? is there a fix or does it need to be replaced. I've tried to reach out to Customer service twice with no response. Any help would be great thanks.

Believe for that size the diodes are run series/parallel in 2 strings. One of the strings failed "open".
Problem is the other string now gets full mA from the driver.. Lifespan is shortened..
What is the output listed on the driver?

It is cheap and easy to fix w/ soldering skills and a multimeter.

How to repair an Orphek OR2

So I have a pair of Orphek OR2 90's, with almost all UV bulbs. Not too long after running them, they both failed. I assumed it was the power supply, and tried to replace it (hint, Orphek won't sell you a powersupply). Turns out that wasn't the problem. The problem was this: Now you might...

www.reef2reef.com

 

[bullseyereef]

I had the same
CS reached out to me and offered a very discounted price on a OR3 replacement

i wish they would respond to me lol

 

[bullseyereef]

Believe for that size the diodes are run series/parallel in 2 strings. One of the strings failed "open".
Problem is the other string now gets full mA from the driver.. Lifespan is shortened..
What is the output listed on the driver?

It is cheap and easy to fix w/ soldering skills and a multimeter.

How to repair an Orphek OR2

So I have a pair of Orphek OR2 90's, with almost all UV bulbs. Not too long after running them, they both failed. I assumed it was the power supply, and tried to replace it (hint, Orphek won't sell you a powersupply). Turns out that wasn't the problem. The problem was this: Now you might...

www.reef2reef.com

ill check this out thanks

 

[vetteguy53081]

i wish they would respond to me lol

They do that during night on weekdays. They’re out of the country

 

[bullseyereef]

They do that during night on weekdays. They’re out of the country

its been a couple weeks...

 

[Hydrored]

@Orphek

@bullseyereef also try emailing [email protected]

 

[vetteguy53081]

its been a couple weeks...

Message again

 

[bullseyereef]

Message again

finally got a reply, id like to think this post helped lol upgraded to a OR3

 

[vetteguy53081]

finally got a reply, id like to think this post helped lol upgraded to a OR3

You’ll love the OR3 difference

 

[bullseyereef]

You’ll love the OR3 difference

I was just doing some research on the difference between the two. Is there an actual noticeable difference?

 

[vetteguy53081]

I was just doing some research on the difference between the two. Is there an actual noticeable difference?

Yes due to the 5wt diodes

 

[Rawesom0]

Believe for that size the diodes are run series/parallel in 2 strings. One of the strings failed "open".
Problem is the other string now gets full mA from the driver.. Lifespan is shortened..
What is the output listed on the driver?

It is cheap and easy to fix w/ soldering skills and a multimeter.

How to repair an Orphek OR2

So I have a pair of Orphek OR2 90's, with almost all UV bulbs. Not too long after running them, they both failed. I assumed it was the power supply, and tried to replace it (hint, Orphek won't sell you a powersupply). Turns out that wasn't the problem. The problem was this: Now you might...

www.reef2reef.com

Believe for that size the diodes are run series/parallel in 2 strings. One of the strings failed "open".
Problem is the other string now gets full mA from the driver.. Lifespan is shortened..
What is the output listed on the driver?

It is cheap and easy to fix w/ soldering skills and a multimeter.

How to repair an Orphek OR2

So I have a pair of Orphek OR2 90's, with almost all UV bulbs. Not too long after running them, they both failed. I assumed it was the power supply, and tried to replace it (hint, Orphek won't sell you a powersupply). Turns out that wasn't the problem. The problem was this: Now you might...

www.reef2reef.com

I have the same problem, took the light apart attempting to fix it and found no obvious problems. Can anyone tell me if it would most likely be a bad led? I tried every solder joint and no burn areas. I would like to fix it if possible

 

[Rawesom0]

Believe for that size the diodes are run series/parallel in 2 strings. One of the strings failed "open".
Problem is the other string now gets full mA from the driver.. Lifespan is shortened..
What is the output listed on the driver?

It is cheap and easy to fix w/ soldering skills and a multimeter.

How to repair an Orphek OR2

So I have a pair of Orphek OR2 90's, with almost all UV bulbs. Not too long after running them, they both failed. I assumed it was the power supply, and tried to replace it (hint, Orphek won't sell you a powersupply). Turns out that wasn't the problem. The problem was this: Now you might...

www.reef2reef.com

Could you give more info on this repair? I have the same problem and I took mine apart to fix it and found no loose solder joints and no leds look burnt. Any help would be appreciated

 

[D3DPrintedThingz]

anyone, by chance, have the same issue with only half of an OR3 bar lighting? I had to fight pretty hard to get this bar, and now only half of it is lighting up :(

 

[oreo54]

anyone, by chance, have the same issue with only half of an OR3 bar lighting? I had to fight pretty hard to get this bar, and now only half of it is lighting up :(

Well that is only 1/2 your problem atm.
You now have 2x the current going down the remaining 1/2.
You can find a dead diode using a digital VOM.

With the light off (and preferably unplugged) set the VOM to low ohms or diode.
Test each diode one by one on the dead channel.

You will of course need to remove the lenses (I believe) to get to the "ears" on the diode
Polarity matters check BOTH ways unless you figure out which side is always plus and which is always negative.

Once the dead diode is found either replace it or jumper over it.

There could also be a broken trace to ALL the diodes
Or a broken trace in-between diodes.

Between diode breaks could be found using the err"out" of one diode to the "out" of the next in line diode.

Anyways diodes will only light dimly.

Concept vid:

 

[bullseyereef]

anyone, by chance, have the same issue with only half of an OR3 bar lighting? I had to fight pretty hard to get this bar, and now only half of it is lighting up :(

I just ended up replacing mine.

 

[D3DPrintedThingz]

I just ended up replacing mine.

At 200 a pop, that is hard to do for me. Lol

 

[bullseyereef]

At 200 a pop, that is hard to do for me. Lol

Hey i get it. But for me it wasn’t worth the time to try and fix it. And if you dont do it correctly you’re buying a new one anyways. Unless its under warranty then they will sent you a replacement.