Plumbing for new sump

  • Thread starter Thread starter dj1982
  • Start date Start date
  • Tagged users Tagged users None

dj1982

New Member
View Badges
Joined
Aug 16, 2019
Messages
1
Reaction score
1
What state or country do you live in
Missouri
Rating - 0%
0   0   0
Hello everyone! I am looking for a little plumbing advice. I currently have an established 90 gallon aquarium that I am going to upgrade the sump on. The current sump setup is in the cabinet under the tank and very difficult to do maintenance on. Plus I would like to transition to the triton method and I currently do not have a refugium. I have purchased a trigger systems triton44 that will be located approximately 8-10 feet below the aquarium. I also have an ecotech vortec L2 which at my head height should move about 1000 gph (for the triton method I believe I need at least 10x my tank volume which would be 900 gph). The overflow area in the tank has a 3/4" pvc for return and a 1" pvc for drainage. I cannot change these because that corner of the tank fits into a corner in a room and I cannot get to it. The output fitting on my new pump is 1.25". I have 3 1" return fittings on the sump. My plan for plumbing is to have 1.25" pvc from the return pump to the tank then downsize to 3/4" to fit the current plumbing going into the tank. For the drainage, I plan to upsize the plumbing under the tank to 1.5" down to the sump then use a wye to downsize to 2 1" pipes into the fittings in the sump. Does this sound reasonable??? I tend to overthink things so any advice would be very much appreciated!
 
Hello everyone! I am looking for a little plumbing advice. I currently have an established 90 gallon aquarium that I am going to upgrade the sump on. The current sump setup is in the cabinet under the tank and very difficult to do maintenance on. Plus I would like to transition to the triton method and I currently do not have a refugium. I have purchased a trigger systems triton44 that will be located approximately 8-10 feet below the aquarium. I also have an ecotech vortec L2 which at my head height should move about 1000 gph (for the triton method I believe I need at least 10x my tank volume which would be 900 gph). The overflow area in the tank has a 3/4" pvc for return and a 1" pvc for drainage. I cannot change these because that corner of the tank fits into a corner in a room and I cannot get to it. The output fitting on my new pump is 1.25". I have 3 1" return fittings on the sump. My plan for plumbing is to have 1.25" pvc from the return pump to the tank then downsize to 3/4" to fit the current plumbing going into the tank. For the drainage, I plan to upsize the plumbing under the tank to 1.5" down to the sump then use a wye to downsize to 2 1" pipes into the fittings in the sump. Does this sound reasonable??? I tend to overthink things so any advice would be very much appreciated!
Sounds like you got it figured out. I’ve wanted to get a larger sump too on my 90 but I don’t think I could wedge a bigger one in there without taking the stand apart. Good luck!
 

TOP 10 Trending Threads

WHAT DO YOU ALWAYS RUN OUT OF AT THE WORST TIME?

  • Salt mix

    Votes: 17 18.9%
  • Fish or coral food

    Votes: 5 5.6%
  • Test kits or reagents

    Votes: 9 10.0%
  • Filter media or replacement fleece

    Votes: 5 5.6%
  • RO/DI filters or supplies

    Votes: 14 15.6%
  • Fragging and repair supplies, like glue or epoxy

    Votes: 10 11.1%
  • I keep a backup of everything

    Votes: 23 25.6%
  • Other (Post in the comments)

    Votes: 7 7.8%
Back
Top
Home
Post thread…
Market
What's new