Return equipment too small?

[benthicBarbarian]

The specs on Waterbox page don't match Saltwateraquarium.com.

https://waterboxaquariums.com/products/aio-15-cube

Waterbox has it listed under freshwater and this is the only 15 peninsula they currently sell. Did they discontinue the 15 saltwater?

It shows the same plumbing you have.

I think they did! I didn’t buy the one off waterbox because it was obviously meant for freshwater. That’s why I went on SaltwaterAquarium and got the one I thought was the saltwater one.

 

[benthicBarbarian]

I usually stay out of sight, but Bless you my son!

I'm busy walking on water, but I think these are available in standard inch tubing sizes sizes I didn't really examine the specs.

I was looking at the pump that was supplied, and I have used something similar (it may have actually been smaller) and they ran perfectly for a few trials until they stopped after about a month of use. I would plan on replacing the pump, if it was mine.

Oh, and for folks who may still think I am, THe LOrd, I hope He hasn't struck me dead for the evil impersonation.

Send flowers to @tbrown if I pass.

Ugh, plumbing messiah or not, you are a life saver.

I found one on Amazon that had better reviews along with some hose.

Does this look sound?

 

[KrisReef]

Yup, from the site
" Return Jets are available in two sizes for either 1/2" to 3/4" ID hose, or 3/4" to 1" ID flexible hose.

The reviews say that the fitting is very tight for 1/2 hose, which is a shame.

This pump would be an excellent replacement if it fits?
https://www.bulkreefsupply.com/sicc...D=2700&indexName=brs_prod_m2_default_products
AI seems to indicate it will fit the chamber dimensions you listed

AI Overview

The Sicce Syncra Silent 1.0 pump is a submersible pump with a flow rate of 251 gallons per hour (GPH). It measures approximately 3.54" x 1.89" x 2.83" (length x width x height). The pump is designed for aquarium use and can be used either submerged or in-line. It also features a synchronous motor, adjustable flow rate, and a long-lasting impeller and shaft.
Edit:

Never mind, but the one you posted is 3/4 inch diameter hose, which is fine just make sure the pump outlet also handles 3/4" and you should be golden.

Start a build thread.

 

[ptrusk]

If you decide to go this way, consider a DC pump. I have a Sicce 1.5(?) and it is quiet but there is a buzz.

I used
Amazon product ASIN B08PQ4KDKSon my 15 cube and it is dead silent. Also controllable. Speed/feed mode. Nice little pump

 

[benthicBarbarian]

Yup, from the site
" Return Jets are available in two sizes for either 1/2" to 3/4" ID hose, or 3/4" to 1" ID flexible hose.

The reviews say that the fitting is very tight for 1/2 hose, which is a shame.

This pump would be an excellent replacement if it fits?
https://www.bulkreefsupply.com/sicc...D=2700&indexName=brs_prod_m2_default_products
AI seems to indicate it will fit the chamber dimensions you listed

AI Overview

The Sicce Syncra Silent 1.0 pump is a submersible pump with a flow rate of 251 gallons per hour (GPH). It measures approximately 3.54" x 1.89" x 2.83" (length x width x height). The pump is designed for aquarium use and can be used either submerged or in-line. It also features a synchronous motor, adjustable flow rate, and a long-lasting impeller and shaft.
Edit:

Never mind, but the one you posted is 3/4 inch diameter hose, which is fine just make sure the pump outlet also handles 3/4" and you should be golden.

Start a build thread.

Thank you so so much I can’t stress this enough.

One thing tho…I can’t find any U return pipes that can fit a 1/2” hose. Based on the reviews as you’ve said, the 3/4” hose would fit the U pipe, but not the sicce 0.5. Would the 1.0 fit in chamber?

 

[KrisReef]

Thank you so so much I can’t stress this enough.

One thing tho…I can’t find any U return pipes that can fit a 1/2” hose. Based on the reviews as you’ve said, the 3/4” hose would fit the U pipe, but not the sicce 0.5. Would the 1.0 fit in chamber?

The Sicce 1.0 on line size (i don't have one to check) should fit. I actually think that the 0.5 and 1.0 sicce use the same return nozzle-hardware, but again I don't have access to these pumps or fittings to verify connectivity. I would find a site or lFS that has them and ask them to figure this one out.

Sorry, I checked my garage and I don't have the smaller Sicce .

 

[benthicBarbarian]

The Sicce 1.0 on line size (i don't have one to check) should fit. I actually think that the 0.5 and 1.0 sicce use the same return nozzle-hardware, but again I don't have access to these pumps or fittings to verify connectivity. I would find a site or lFS that has them and ask them to figure this one out.

Sorry, I checked my garage and I don't have the smaller Sicce .

Hey Kris!

Just came here to give you a huge thanks! Everything fit like a glove. I decided to get a JBJ pump instead of a sicce simply for the fact it had a 3/4 fitting.

Again, thanks SOOOOOOoooooooOOoo much!!!

 

[KrisReef]

Hey Kris!

Just came here to give you a huge thanks! Everything fit like a glove. I decided to get a JBJ pump instead of a sicce simply for the fact it had a 3/4 fitting.

Again, thanks SOOOOOOoooooooOOoo much!!!

I am super happy to hear that you’re making progress and am glad that I can be helpful once in awhile!

@tbrown - I won this one

bB, you might want to get a bulkhead and plug up the original hole for best results?

Thanks for the update, the tank looks great.