Why do Gate valves cost so much?

squidarcher

Active Member
View Badges
Joined
Sep 28, 2020
Messages
274
Reaction score
219
Location
USA
What state or country do you live in
Maryland
Rating - 0%
0   0   0
I just ordered and Innovative Marine 150 lagoon, with a bean animal overflow system. I know I have to put gate valves on the primary and secondary overflow drains, but I cannot find 1-1/2'' gate valves for under $100. The only cheap ones I can find are the Valterra ones, would those work? Am I just not looking in the right place? Any advice or recommendations would be helpful!
 
They are expensive, no clue why. I’m replumbing a tank and it’s not cheap. Specially if you mess up…
 
I just ordered and Innovative Marine 150 lagoon, with a bean animal overflow system. I know I have to put gate valves on the primary and secondary overflow drains, but I cannot find 1-1/2'' gate valves for under $100. The only cheap ones I can find are the Valterra ones, would those work? Am I just not looking in the right place? Any advice or recommendations would be helpful!
I purchased mine from Bulk Reef Supply and Lowes. They were reasonably priced.
 
I ran inexpensive gate valves for years and never had any major issue. On my new build, I went with a Spears but, the tank isn't wet yet so I'm not able to tell you if it's made a big difference. Get a gate valve you can afford and go with that until you are able to go with a Spears valve later if that is the spot your in.
 
Had similar question when i started my build a couple of years ago. What i found was the following:

Easier to adjust: Not that you will do this often, however over time i found the cheaper gate valve will "stick" meaning difficult to turn the adjustment handle over time.

In my experience they can develop a small leak around the adjustment knob. I cant think of the brand... but i did buy off of Amazon. I went with the more expensive spears and it works and operates the same as it did the day i glued it in. Just my 2 cents.

1672844412141.png
 
Had similar question when i started my build a couple of years ago. What i found was the following:

Easier to adjust: Not that you will do this often, however over time i found the cheaper gate valve will "stick" meaning difficult to turn the adjustment handle over time.

In my experience they can develop a small leak around the adjustment knob. I cant think of the brand... but i did buy off of Amazon. I went with the more expensive spears and it works and operates the same as it did the day i glued it in. Just my 2 cents.

1672844412141.png
dang. Guy knows what he’s doing.
 
The 1 1/2" size makes it substantially more than a 1" valve. They are about 1/4 the cost.
 
You'll eventually need to pull it and clean it(spiriod worms, snails crawls down it, etc). Pony up for the spears with unions, you'll thank me down the road when you need to clean it.
 
You'll eventually need to pull it and clean it(spiriod worms, snails crawls down it, etc). Pony up for the spears with unions, you'll thank me down the road when you need to clean it.
Forgot to mention that... unions are everything!!
 
Reduce your drain to one inch going into the sump and buy the schedule 40 gate valve. You only need a gate valve on the primary.

I would have never bought their sump or any fancy type limiting sump as a 40 breeder, 60 breeder or 75g tank is much easier to customize and less than half the cost.

I have a 40 breeder sump and my gate valve is just slip fitted.
 
Last edited:
Had similar question when i started my build a couple of years ago. What i found was the following:

Easier to adjust: Not that you will do this often, however over time i found the cheaper gate valve will "stick" meaning difficult to turn the adjustment handle over time.

In my experience they can develop a small leak around the adjustment knob. I cant think of the brand... but i did buy off of Amazon. I went with the more expensive spears and it works and operates the same as it did the day i glued it in. Just my 2 cents.

1672844412141.png
Do you think I would be fine if I reduced my primary drain down to 1 inch?
 
Reduce your drain to one inch going into the sump and buy the schedule 40 gate valve. You only need a gate valve on the primary.

I would have never bought their sump or any fancy type limiting sump as a 40 breeder, 60 breeder or 75g tank is much easier to customize and less than half the cost.

I have a 40 breeder sump and my gate valve is just slip fitted.
I actually got a 55 gallon and added acrylic baffles. I set it up for my 75 and now I want to use it for the 150.
 
Had similar question when i started my build a couple of years ago. What i found was the following:

Easier to adjust: Not that you will do this often, however over time i found the cheaper gate valve will "stick" meaning difficult to turn the adjustment handle over time.

In my experience they can develop a small leak around the adjustment knob. I cant think of the brand... but i did buy off of Amazon. I went with the more expensive spears and it works and operates the same as it did the day i glued it in. Just my 2 cents.

1672844412141.png
That is sharp!
 

TOP 10 Trending Threads

HOW DO YOU HANDLE HOLIDAY DECORATING AROUND YOUR REEF?

  • I decorate the tank or stand

    Votes: 1 4.3%
  • I decorate AROUND the tank or stand

    Votes: 4 17.4%
  • I add one small seasonal touch but keep it very basic

    Votes: 0 0.0%
  • I take a holiday photo, but don’t decorate the space

    Votes: 0 0.0%
  • I leave the reef area as it is

    Votes: 14 60.9%
  • We don’t decorate for the holidays

    Votes: 4 17.4%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new