3D Printing thread

[GrizFyrFyter]

I didn't bother to contact Ecotech because it was my fault it broke... I'm sure if I did, they wouldn't have hesitated to work something out.

Purple was the first draft, thinking that I would have to do some adjustments to the design, but everything lined up perfectly. Even the plastic tab that locked the motor harness to the frame slid in and lined up perfectly. So no need to reprint another.

That's impressive design skills. I'd have to do it wrong 4 or 5 times :(

 

[TheHarold]

I didn't bother to contact Ecotech because it was my fault it broke... I'm sure if I did, they wouldn't have hesitated to work something out.

Purple was the first draft, thinking that I would have to do some adjustments to the design, but everything lined up perfectly. Even the plastic tab that locked the motor harness to the frame slid in and lined up perfectly. So no need to reprint another.

Yeah they said they would fix it free IF the motor was undamaged—- just put it into a new housing. Luckily that was the case.

That’s some impressive modeling!

 

[TheHarold]

Does anyone have a STL for a reeflink mount? I thought there used to be one on thingiverse, but I guess they took it down.

@GrizFyrFyter was that yours?


edit:

Nevermind, I found a model online for $1. Fair enough :)

 

[GrizFyrFyter]

Does anyone have a STL for a reeflink mount? I thought there used to be one on thingiverse, but I guess they took it down.

@GrizFyrFyter was that yours?


edit:

Nevermind, I found a model online for $1. Fair enough :)

I have one. I thought I put it up but maybe not.

 

[GrizFyrFyter]

I didn't. I'll post it when I get back in the shop tomorrow.

 

[TheHarold]

I didn't. I'll post it when I get back in the shop tomorrow.

No worries. I was feeling lazy so found one online for $1 lol. More efficient than spending 20 minutes modeling and a test fit.

 

[Palluk33]

OK guys just order Creality Ender 3 Pro 3D Printer
What material is reef save? Appreciate for any help

 

[TheHarold]

OK guys just order Creality Ender 3 Pro 3D Printer
What material is reef save? Appreciate for any help

PETG.

 

[Palluk33]

Is anyone using Creality Ender 3 Pro ?

 

[TheHarold]

Is anyone using Creality Ender 3 Pro ?

I used to- had several, but over time upgraded printers. Currently I know @dantimdad us using them

 

[Palluk33]

I used to- had several, but over time upgraded printers. Currently I know @dantimdad us using them

Can I print PETG with it?

 

[TheHarold]

Can I print PETG with it?

I did, though I upgraded to an aluminum extruder for reliability.

 

[Palluk33]

I did, though I upgraded to an aluminum extruder for reliability.

Thank you

 

[dantimdad]

Can I print PETG with it?

I do daily. As @TheHarold said upgrade the extruder to aluminum one and make sure your extrusion rate is set properly.

 

[Palluk33]

I do daily. As @TheHarold said upgrade the extruder to aluminum one and make sure your extrusion rate is set properly.

Where can I get aluminum extruder?

 

[TheHarold]

Where can I get aluminum extruder?

Amazon. eBay. Aliexpress. Wherever lol

 

[Palluk33]

Amazon. eBay. Aliexpress. Wherever lol

Thx

 

[dantimdad]

https://www.amazon.com/WINSINN-Extr...ruder+upgrade&qid=1562008503&s=gateway&sr=8-6


These are what I use.

 

[Palluk33]

https://www.amazon.com/WINSINN-Extr...ruder+upgrade&qid=1562008503&s=gateway&sr=8-6


These are what I use.

Thank you, should I upgrade anything else?

 

[dantimdad]

I would change the bowden tube out and the ends to it. Just my habit with new ones. I have 3.

Also, print the side spool mount it makes the path of the filament much, much easier on the printer.

And, upgrade the bed springs. Makes it less often you have to level the bed and it's cheap.