commod0re's UNS R90 Build

Well we made it to November and the tank is still there. Did a 25 gallon water change and siphoned some of the sand and all the rocks and actually, despite the color, it seems a lot of the nuisance algae has died. I never did that second dose of flux either lol

Seems like there’s still diatoms and maybe a bit of cyano as well but I siphoned out as much of that as I could. The clean up crew that’s still in there looks OK

Fallow period is definitely over, at long last, so any day now we’ll move the wrasse into the tank…. i’m just nervous since she’s been doing so well in the little tank. There’s a huge amount of amphipods built up in the big tank for her to snack on though which is great. I still need to clean up the new quarantine tank as well but I will take care of that soon…
 
How high is your fleece roller sensor sitting above water level? I installed my set yesterday and with my running sump level about 9” the sensor is still about 2” off top of water. I would not want the front chamber to fluctuate that much as it will inevitably mess with my ATO. Did you have to do anything special?
 
How high is your fleece roller sensor sitting above water level? I installed my set yesterday and with my running sump level about 9” the sensor is still about 2” off top of water. I would not want the front chamber to fluctuate that much as it will inevitably mess with my ATO. Did you have to do anything special?
It won’t raise the water level of the whole chamber that far, just inside the fleece roller itself, so the total volume of fluctuation is actually quite small
 
It won’t raise the water level of the whole chamber that far, just inside the fleece roller itself, so the total volume of fluctuation is actually quite small
Ah, now that I think about it you’re absolutely correct. I was looking at it backwards. Sometimes it’s better to air out questions to others to see the whole picture 😅 I’m in the process of moving over coral and breaking down my other tank so I got a lot going on inside my head atm 🫠
 
Ah, now that I think about it you’re absolutely correct. I was looking at it backwards. Sometimes it’s better to air out questions to others to see the whole picture 😅 I’m in the process of moving over coral and breaking down my other tank so I got a lot going on inside my head atm 🫠
I did have another one for ya. I was looking at my roller chamber and it seems the water doesn’t make it to the front roller really at all. I can’t tell if it’s just all pouring through the 1st roller closest to the spout or it’s draining around the tray they are sitting on. Would love to know how yours is.
 
The new fleece rollers have been working well. I can’t think of anything else really to say this week so here are a couple of pictures of me target feeding the wrasse some thawed cyclops
IMG_3589.jpeg

IMG_3590.jpeg


Still considering some names for her. Two current front runners are Wrasseberry and Tia Dalma
+1 for Wrasseberry. That’s so cute!
 
I did have another one for ya. I was looking at my roller chamber and it seems the water doesn’t make it to the front roller really at all. I can’t tell if it’s just all pouring through the 1st roller closest to the spout or it’s draining around the tray they are sitting on. Would love to know how yours is.
How do you have them oriented? I played with mine for a long time when I was getting them set up and discovered two things that could be related to this:

1. The fit between the sock holder and the sock chamber is fairly loose and water easily leaks around the sides bypassing the fleece rollers completely. Not a ton but some. I used a 3D printer to print pieces to both fill the gaps and also make the plate more rigid

2. When the first roller is still clean most of the water will drain through it and not much will make it to the second/front roller. Once that roller gets dirty more water will flow over it and into the second roller. Based on that I put the roller with the sensor in the front slot, so that it only rolls when both are finally dirty
 
How do you have them oriented? I played with mine for a long time when I was getting them set up and discovered two things that could be related to this:

1. The fit between the sock holder and the sock chamber is fairly loose and water easily leaks around the sides bypassing the fleece rollers completely. Not a ton but some. I used a 3D printer to print pieces to both fill the gaps and also make the plate more rigid

2. When the first roller is still clean most of the water will drain through it and not much will make it to the second/front roller. Once that roller gets dirty more water will flow over it and into the second roller. Based on that I put the roller with the sensor in the front slot, so that it only rolls when both are finally dirty
I have them currently positioned with the fill port towards the skimmer compartment, and I also placed the sensor in the front. Sounds like I need to get a 3d printer sooner than later to make misc things ha. Maybe you could show me what you went with so I can copy? Or if you don’t mind printing more I’d gladly pay
 
Hi @Char.toombes, with water entering from one direction, it’s normal for the two rollers to receive different amounts of flow. One may get dirty faster, but both should collect debris over time.

  • Place the Main unit in the position that gets dirty more slowly. Since the Main and Extension advance together, the slower-loading roll will trigger both motors once it needs fresh fleece, giving both rolls time to collect debris.
  • Different water-blocker heights may help balance the flow. Where your setup allows it, try the taller blocker on the roller receiving more water and the lower blocker on the one receiving less. Only use the lower blocker if it still seals the opening properly and keeps water from bypassing the fleece. This may help distribute the flow more evenly between the two rollers.
 
I went down to Sea King yesterday and got a couple new corals, a container of AFR powder, and some snails and hermit crabs. This is my first time with the powder instead of liquid but holy crap the price efficiency difference is crazy! 800g of powder costs only a little more than 1L of liquid but mixes up 5L of actual AFR. At my current dosing rate this amount it will last me almost 2 years, vs a little over 3 months for the bottle of liquid, for about the same money. Very cool


Coral-wise: got a new little duncan and a couple of zoas to start restoring the zoa garden. Most of the old ones did not make it through the algae unfortunately. But on the flip side of that: the nuisance algae nobody wanted to eat is basically all dead and gone now so that one fluconazole treatment really worked!

The two leather corals are still thriving. The GSPs are huge as well. Also that mushroom coral I thought I lost? It reappeared towards the back of the tank lol

So things are starting to look up again basically. New tank is finally over 6 months old so I think things will get a bit easier from here
 
I have them currently positioned with the fill port towards the skimmer compartment, and I also placed the sensor in the front. Sounds like I need to get a 3d printer sooner than later to make misc things ha. Maybe you could show me what you went with so I can copy? Or if you don’t mind printing more I’d gladly pay
I shared some pics in this thread but I can also share my files or print it for you if you’d like
 
I went down to Sea King yesterday and got a couple new corals, a container of AFR powder, and some snails and hermit crabs. This is my first time with the powder instead of liquid but holy crap the price efficiency difference is crazy! 800g of powder costs only a little more than 1L of liquid but mixes up 5L of actual AFR. At my current dosing rate this amount it will last me almost 2 years, vs a little over 3 months for the bottle of liquid, for about the same money. Very cool


Coral-wise: got a new little duncan and a couple of zoas to start restoring the zoa garden. Most of the old ones did not make it through the algae unfortunately. But on the flip side of that: the nuisance algae nobody wanted to eat is basically all dead and gone now so that one fluconazole treatment really worked!

The two leather corals are still thriving. The GSPs are huge as well. Also that mushroom coral I thought I lost? It reappeared towards the back of the tank lol

So things are starting to look up again basically. New tank is finally over 6 months old so I think things will get a bit easier from here
I’ve been using the AFR powder as well, it’s almost time to get more. It’s sooo much of a better deal. I’ve been mixing it just by stirring. I need to get an auto stirrer soon.

I would offer you some zoas to fill out your garden but everything I’ve got them on is likely also infested with Vermetid and I wouldn’t want to do that to you.
 

TOP 10 Trending Threads

HOW WOULD YOU FEEL ABOUT RECEIVING A FISH OR CORAL AS A HOLIDAY GIFT?

  • I’d love one, as long as it’s a species I chose

    Votes: 26 22.8%
  • I’d trust someone who knows my tank to choose

    Votes: 10 8.8%
  • I’d rather get a gift card and pick it myself

    Votes: 45 39.5%
  • I’d prefer gear or supplies instead

    Votes: 3 2.6%
  • Please don’t surprise me with livestock

    Votes: 30 26.3%
  • Other (Post in the comments)

    Votes: 0 0.0%
Back
Top
Home
Post thread…
Market
What's new