TTNuge
Active Member
Agreed, not everyone is scouring every bit of info they can find like some of us. I' m such a gadget junkie and love researching things so this is right up my alley.
Trident FAQ (official)
- Thread starter Terence
- Start date
- Tagged users None
Agreed, not everyone is scouring every bit of info they can find like some of us. I' m such a gadget junkie and love researching things so this is right up my alley.
Chris155hp
Well-Known Member
Got mine today! Believe in unicorns!!! I have a genuine question for @Terence. The tops of the reagents, should they be put on tight (in the unit) or loosely as to not cause a vacuum? Better said, do the lines going into the reagent “down spouts” allow for air to pass into bottles? Thanks
Bobek
Active Member
When did u order?Got mine today! Believe in unicorns!!! I have a genuine question for @Terence. The tops of the reagents, should they be put on tight (in the unit) or loosely as to not cause a vacuum? Better said, do the lines going into the reagent “down spouts” allow for air to pass into bottles? Thanks
Just screw the cap/needle assemblies onto the bottles fully. Neither loose nor really tight. The hole where the 90 degree elbow goes through provides a tiny vent, sufficient to prevent a vacuum from forming as reagent gets consumed.
Chris155hp
Well-Known Member
TX_Punisher
Valuable Member
- Joined
- Jun 8, 2017
- Messages
- 1,420
- Reaction score
- 778
Let us know how the setup goes. Looking forward to getting one.
TX_Punisher
Valuable Member
- Joined
- Jun 8, 2017
- Messages
- 1,420
- Reaction score
- 778
Nice. Thanks for sharing.
I'm using a 40g breeder as my sump. The orange clip is not large enough to fit over the side of that tank - the plastic rim is too big. I just realized, sitting here at work, that I should have clipped it over a glass baffle. I'll do that when I get home.
I put the Trident on a small, two drawer nightstand sort of thing which is right next to the tank. You can see part of it in the photos at the top. I could build a shelf for it under the tank, but I'm not sure that I want to. For now, I'm going to leave it outside the tank. As I said, it was very easy to setup. After doing the initial steps, I went to my son's game and proceeded check for the first test results on my phone. Apparently too much, as my wife noticed and said something. :)
I intend to run the calibration on it tonight, since it will have been running for 3 days.
I put the Trident on a small, two drawer nightstand sort of thing which is right next to the tank. You can see part of it in the photos at the top. I could build a shelf for it under the tank, but I'm not sure that I want to. For now, I'm going to leave it outside the tank. As I said, it was very easy to setup. After doing the initial steps, I went to my son's game and proceeded check for the first test results on my phone. Apparently too much, as my wife noticed and said something. :)
I intend to run the calibration on it tonight, since it will have been running for 3 days.
We issued a firmware update today: 5.05_5B19. Make sure to update to that and the Trident before completing the calibration. If it shows no update is available, then reboot your Apex and wait a couple minutes. Full information regarding the firmware update can be found here
The Trident only does a self-check and test for sample water after a firmware update; it does not run an Alk or Combined test at that time; it will run the next scheduled Alk or Combined test per the schedule you have configured.
Irongolem411
Active Member
What was the intermittent calibration anomaly?
Since I calibrated already, how would I know if it happened?
Since I calibrated already, how would I know if it happened?
Ran the software update remotely yesterday afternoon. Then I updated the Trident firmware (again, remotely). Last night, I ran the calibration. Simple and painless.
After running the calibration, I did notice that the Apex Fusion logged a pretty high Ca - it was 468 on the graph. I think that coincided with the calibration test. At that point, the tile read 425, which was the calibration solution. As of this morning, my Ca was reading 418. This is about what I would expect.
I should have taken some screen shots of Trident tile before and after the calibration. However, from memory, the only reading that changed much was Ca. It was reading closer to 385-390 before the calibration and is 418 after. That's a long way of saying that the calibration from Neptune was very accurate for Alk and Mg from the factory.
I continue to be very happy with the Trident.
After running the calibration, I did notice that the Apex Fusion logged a pretty high Ca - it was 468 on the graph. I think that coincided with the calibration test. At that point, the tile read 425, which was the calibration solution. As of this morning, my Ca was reading 418. This is about what I would expect.
I should have taken some screen shots of Trident tile before and after the calibration. However, from memory, the only reading that changed much was Ca. It was reading closer to 385-390 before the calibration and is 418 after. That's a long way of saying that the calibration from Neptune was very accurate for Alk and Mg from the factory.
I continue to be very happy with the Trident.
Similar threads
- Price: $950
- Shipping Available
