Show Off and Discuss Your Red Sea Reefer Series
- Thread starter Broadfield
- Start date
- Tagged users None
sittnon18s
Community Member
Do you have a pic of them installed in a sump?
PugsAndFish
Well-Known Member
- Joined
- Jul 10, 2018
- Messages
- 554
- Reaction score
- 255
would the skimmer come before or after the refugium with this baffle (170)?light roll-out.
https://www.reef2reef.com/threads/red-sea-v1-sump-baffle-kits.513928/
Made from 100% high quality, cast acrylic, these baffle kits will give your V1 Red Sea sump separate skimmer and refugium area. The kits utilize my renown Octo Pods™, with the strongest neodymium magnets available, along with the very strict quality control standards I use to make the pods. These are absolutely the most secure, toughest Red Sea sump baffle kits available. Fully designed and made by myself, these kits are also adjustable in case there are any dimension variations from the manufacturer.
I use N52 neodymium magnets. Rare earth magnets are not reef safe on their own, so I fabricate custom acrylic pods that encapsulate the magnets and keep them away from your water. Please visit the magnet warning page for more information on these magnets.
Most of my products are made to order and BY HAND! Please allow 10 days for fabrication time (longer for Octo Lids™) Shipping prices listed are to the contiguous U.S. Please contact us if you live elsewhere and want a shipping quote.
Order HERE.
170 - $75.99
250 - $85.99
350 - 95.99
425 - 105.99
525 - 115.99
525, 425 and 350:
250 and 170:
(magnets not installed in photos and does not show bolts and wingnuts that hold the two pieces together. you can see them in the photo above)
light roll-out.
https://www.reef2reef.com/threads/red-sea-v1-sump-baffle-kits.513928/
Made from 100% high quality, cast acrylic, these baffle kits will give your V1 Red Sea sump separate skimmer and refugium area. The kits utilize my renown Octo Pods™, with the strongest neodymium magnets available, along with the very strict quality control standards I use to make the pods. These are absolutely the most secure, toughest Red Sea sump baffle kits available. Fully designed and made by myself, these kits are also adjustable in case there are any dimension variations from the manufacturer.
I use N52 neodymium magnets. Rare earth magnets are not reef safe on their own, so I fabricate custom acrylic pods that encapsulate the magnets and keep them away from your water. Please visit the magnet warning page for more information on these magnets.
Most of my products are made to order and BY HAND! Please allow 10 days for fabrication time (longer for Octo Lids™) Shipping prices listed are to the contiguous U.S. Please contact us if you live elsewhere and want a shipping quote.
Order HERE.
170 - $75.99
250 - $85.99
350 - 95.99
425 - 105.99
525 - 115.99
525, 425 and 350:
250 and 170:
(magnets not installed in photos and does not show bolts and wingnuts that hold the two pieces together. you can see them in the photo above)
but wait, there’s more!
how about a clear panel in the center of the baffle (on the larger sizes)?
and one of these for 50% when purchased with a baffle kit!!!
https://octoaquatics.com/octo-strong-heater-holder/
Last edited:
Natedogg559
Nathan
So re did my control room in the 625xxl and built a little stand for it not everything is done but here is what it looks like so far. The top opens up where I have access to all my outlets and battery packs. Also had a question have any of you drilled a hole in the left pannel to feed your dosing lines through? I wanted to do this instead of feeding them around the back but not sure if it will mess with the structural integrity of the stand , any input would be awesome.
Dan Snyder
Active Member
So re did my control room in the 625xxl and built a little stand for it not everything is done but here is what it looks like so far. The top opens up where I have access to all my outlets and battery packs. Also had a question have any of you drilled a hole in the left pannel to feed your dosing lines through? I wanted to do this instead of feeding them around the back but not sure if it will mess with the structural integrity of the stand , any input would be awesome.
I did a 2” hole on my XXL 750 which is pretty much full of lines and wires. Don’t think it weakens the structural integrity at all.
I did the same but just make sure to paint or seal the exposed wood so that water won’t get in the wood and expand it.
Dan Snyder
Active Member
Ouch if you get water in there you got bigger problems. [emoji51]
Mordie101
Well-Known Member
Anyone tried the Nero 5 power head on the 250? I’m starting my reefer 250 tank early January and trying to buy all the set up early to have time to piece it out. Really looking into these since the AI app will work on lights and those power heads.
CamInDFW
Community Member
I've been using it on my 170 since release - I like it quite a bit. I've had zero issues with it so far. Presently, it's modes aren't as "robust" as say an MP10 but, I imagine they will expand over time.
Z3speed4me
Well-Known Member
Hey all!
Working up motivation for a build thread...still trying to level these silly doors!
In the meantime, are there any surface mount hinges, so I don't have to bore out holes with a jig if I want to make compartments in the right side?
Tank pics bc well isn't that the purpose of this thread?
Working up motivation for a build thread...still trying to level these silly doors!
In the meantime, are there any surface mount hinges, so I don't have to bore out holes with a jig if I want to make compartments in the right side?
Tank pics bc well isn't that the purpose of this thread?
Similar threads
