Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
The story of Flippers reef started long ago..........

In a time before a thing called "The Internet"existed. Land locked Missouri, mid western U.S.A. back in 1993. I had just got out of the army in 1992 and got busy starting a family.

See, I had fresh water tanks off and on since I was very young and one summer night back in 93, while out to dinner with my wife and daughter, we had to wait for a table at a restaurant. We decided to take a walk down the strip mall near by to burn some time and unknown to me, there before me was a "saltwater fish store"! Looking in windows with eyes wide and mouth open, like a kid on Christmas Day! I had to go in! The rest is history and a "True Aquatic Addiction" permanently took hold.

Since then, a couple houses and numerous saltwater tanks later, our journey brings us to March 2015.......

This is Flippers current build thread.....

Tank: Marineland standard 6', 125 gallon RR

Stand: DIY

Canopy: DIY, 2, 120mm computer case fans

Sump tank: 6', 125 gallon, basement. DIY sump stand

Water changing station: 2, 33 gallon grey Brute trash cans connected via recirculation manifold. Danner mag 5

Skimmer: Reef Octopus classic nwb150

Heaters: 3, 150w, controlled by Inkbird Itc 308.

Return pump: Panworld 150ps

DT Wave pumps: 2, Jebao RW 15's on JB wave controller

ATO: autotopoff.com redundant float switch controlled, 16 gallon Ace rotomold conical tank. Jebao pump, internal

DT lights: 3, modified 165w Mars Aqua units. LED layout mod to SB reef lights diode layout

RO/DI: BRS 6 stage





New house = New tank! Planing stage was at least a 6' tank, but not too big due to funds. A new 6' 125 at $350 was to good to pass up. Knowing I was going to to do a basement sump on this one, I found a used 6' 125 that's was scratched up for $100.

Stand build was based on "Rocket engineers" design. 2x4's and 2x6's design. Wood screws and wood glue. 1/4" plywood skinned. No top. Doors hand built.


320e51922b3091caf2fea04063ba8c71.jpg




Interior and exterior painted semi gloss:

1cd7d9565628b5112ff31bb215b93915.jpg
 
Last edited:
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
Next the basement!

This is a unfinished basement in this house and that meant I had unlimited possibilities!

First off there was no access to electricity and no easy access to water!

I had to do both!

Let's cut the main water line!

eaacc10927337254e37244df6db69b19.jpg


852ff7ef958ca3251d0da3fda3d338b5.jpg


Electric

6954433a377452eba07596cb7e47dcab.jpg


Need a sink, plumbing and water changing station

04f23893efb662a925fc71d2fa53e388.jpg


6ac1a886715efdd1d72e60b86dc59f90.jpg
 
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
On to building a sump stand

af1cd3816f2c3c64890322a83aa72000.jpg


288cb4022158d2722c773b6dc0085c10.jpg


At first I used a 20 gallon trash can for the ATO and needed a stand for it

4f7219bc65f002d86038724655275558.jpg


This is the ATO now:

2a33759352e7a0e7e9725f1800867044.jpg


Add RO/DI and sump on the stand

132e4f7b73ea94e22ce1ee35669d5142.jpg
 
Last edited:
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
Now my living room area where the DT was to go has a large span and I didn't want the the floor to bounce with the weight of the tank. So I sistered the floor joists under the tank, placed a 4x4 under the length of the tank and added floor jacks for support

228114d511c29f7d680898e952889e14.jpg


With the DT stand and tank set upstairs, it was time for the drains. I choose to do an emergency drain as well

40af757eae05264117d22220ad2a9804.jpg


104699778fc76cb2c9ea0cd88dd11f53.jpg


b0d21c3d29da1d727debba63d44c94ac.jpg


I wanted not to pack buckets, so a drain from the sump to the house was needed

93f439e0f089d25780b8fe65ffb10a12.jpg
 
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
Went salty and after the cycle in went some easy corals

46a86fb83ddc611a2ddc8d04a5e840f3.jpg


I started out with T5's over this tank. Aquticlife 8 bulb fixture

51e3365edab0a30bf62591495643b309.jpg


But got tired of changing bulbs (ATI) and the cost involved, so in October of 2016 I switched over to the Mars Aqua units. Corals responded very well with the LED's.

c4a9e424468e7a2223a7ff7b73564c0a.jpg


And as of this month I modded them by replacing some of the diodes to mimic the SB reeflights layout

a4096cff411f3de518b4440ab8618055.jpg


d2371f28b01c652ca79701a2ebb5ff9f.jpg


So that's about it. I've been slowly adding more and more SPS frags. Some acropora, some montipora caps and digitatas.

Fish as of right now:

Tomini tang
Paired ocellaris clownfish
mandarin dragonet goby
yellow coris wrasse
Vermiculite leopard wrasse

I love this hobby! Fins up and happy reefing!
 
Last edited:
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
Was running filter socks for the longest time and up and decided not to run them anymore.

Problem ....... salt spray from the drains.

Solution ........ temporary "bubble box". Going to build one out of acrylic soon. Cut out at the bottom allows water out, but keeps bubbles in. Built one out of acrylic years ago for a smaller system and it worked very well. Looks ghetto, but hey, works.

1a91861df14db17941eed07e6ad3c5ad.jpg


e346ca111ec570306f5aba7f07cd7d46.jpg
 

Fishnerd7

Community Member
View Badges
Joined
Aug 7, 2017
Messages
72
Reaction score
75
Location
California
Rating - 0%
0   0   0
Newbie here..incredible build!!!!! This is the second time in only a few weeks I've heard of no filter socks? How do you clean out all the junk? Where does it collect? Love the canopy as well. Is it heavy? I'd like to build something that beefy but worry about the weight on my frame.
 
OP
OP
F

Flippers4pups

Fins up since 1993
View Badges
Joined
Jun 21, 2016
Messages
18,499
Reaction score
60,635
Location
Lake Saint Louis, Mo
Rating - 0%
0   0   0
Thank you!

Detritus settles in the first chamber of the sump, the skimmer section. Once a month I just vacuum it out.

The construction of the canopy was designed to minimize weight buy using the 1" frame and 1/4 plywood skin. Many other canopy builders use 1/2" solid wood in their construction, which adds significantly to the weight.

The canopy weights around 50lbs. Not much weight at all.

:)
 

Mastering the art of locking and unlocking water pathways: What type of valves do you have on your aquarium plumbing?

  • Ball valves.

    Votes: 42 48.3%
  • Gate valves.

    Votes: 46 52.9%
  • Check valves.

    Votes: 20 23.0%
  • None.

    Votes: 22 25.3%
  • Other.

    Votes: 9 10.3%
Back
Top