Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I don't recall if I had that bend in the hose. I will try to take a look when I get home. Do you have a rubber gasket or anything on the display side of the over flow?Looks great! I just set up the INT 100 and I wonder if you have this same issue....in order to get the return standpipe into the locline bulkhead, the nylon hose needs to bend a little...I was concerned this could put pressure on the bulkhead or bottom glass....I spoke with IM and they think its fine, I just wonder if its something you noticed. Here is a pic of mine
Thanks. Ya, I just use the gasket they sent with the bulkheadI don't recall if I had that bend in the hose. I will try to take a look when I get home. Do you have a rubber gasket or anything on the display side of the over flow?
I trimmed mine as well but the return hole is simply too far from the locline bulkhead to reach there without bending....at least with mine its like thatI ended up trimming about 2” off my tubing. I took a lil off at a time until the fit was right and didn’t have tension.
I just tried to look at my return stand pipe and I don’t see much of a bend. But it hard for me to see back there and there is water. Maybe you can take off the rubber o ring from the display side and it will sit alittle farther back.Looks great! I just set up the INT 100 and I wonder if you have this same issue....in order to get the return standpipe into the locline bulkhead, the nylon hose needs to bend a little...I was concerned this could put pressure on the bulkhead or bottom glass....I spoke with IM and they think its fine, I just wonder if its something you noticed. Here is a pic of mine
Thanks...ya it probably would but then water would leak into the overflow...the bend is actually very smallI just tried to look at my return stand pipe and I don’t see much of a bend. But it hard for me to see back there and there is water. Maybe you can take off the rubber o ring from the display side and it will sit alittle farther back.
Thanks for the advice. I had already ordered the osmolator. I figured I just go with the one that is supposed to me reliable.Hey man check out the innovative marine ato. The pump is on sale at BRS. I like it a lot, unique differences from others that I think are important to me. Runs dry no prob, level sensors that are redundant and don’t rely on light or float switches. Check it out
Auqa Gadget Titanium HydroFill ATO Pump
Innovative Marine has designed a low voltage, high performance air lift pump specifically for auto top off controllers. The Auqa Gadget HydroFill ATO Pump System works with the HydroFill ATO Controller System or ATO of your choice. Complete with Lift pump, return pipe and acrylic Max output of...www.bulkreefsupply.com
Shop | Innovative Marine Products
Shop Now | Innovative Marine's Official Store | Free Shipping on all orders* | NUVO aquariums and saltwater reef supplies.www.innovative-marine.com
I am happy with the INT, but the overflow takes up a lot of room. I would have gone with the EXT, but it pushes the tank forward too much for where I wanted to put it.Good choice. Always go Tunze Osmolator 3155. It is the most proven thing out there and replacement parts are cheap. It has fantastically simple and reliable safe guards. It will even keep working if the head unit on your controller locks up. I wouldn't put anything else on my tank.
Your tank is fantastic. Considering going a similar route with the EXT line. I like having space behind my tank and a couple pieces of removable trim can hide the plumbing while still providing easy access.
Hey Lee, thanks. Sure, I’ll send you a message- Hope the tank shows soon !Hi, Nice tank... Have a 75 EXT stuck at a fright dock in Abq, guess they are not in a hurry to get it to me even though I'm 5 miles away. Any way I was wondering if you could take a measurement with the front doors closed to the outside back of the stand? Trying to plan hardware.
Thanks,
Lee
Hey, how do you like the Vectra? Does it keep the overflow water level consistent?I am happy with the INT, but the overflow takes up a lot of room. I would have gone with the EXT, but it pushes the tank forward too much for where I wanted to put it.
I have been happy with the vectraHey, how do you like the Vectra? Does it keep the overflow water level consistent?