Show Off and Discuss Your Red Sea Reefer Series

[jwt1603]

Setting up my new 525XL. Which power head would work best? I'm thinking of two Gyre 250's.

 

[jwt1603]

Setting up my new 525XL. Which power head would work best? I'm thinking of two Gyre 250's.

I should have added that I'm brand new to this and getting in slowly so for now I don't have a controller to run everything on a single interface.

 

[Scubabum]

Setting up my new 525XL. Which power head would work best? I'm thinking of two Gyre 250's.

I have two Gyre 250's on my Reefer 525XL. All the flow you will ever need. Good choice.

 

[jwt1603]

I have two Gyre 250's on my Reefer 525XL. All the flow you will ever need. Good choice.

Thanks.

 

[My90Sea]

DOES ANYONE KNOW WHERE TO BUY REPLACEMENT PARTS FOR 750 xxl? I NEED ALL THE PLUMBING PARTS

THANKS

 

[kinetic]

DOES ANYONE KNOW WHERE TO BUY REPLACEMENT PARTS FOR 750 xxl? I NEED ALL THE PLUMBING PARTS

THANKS

REACH OUT TO RED SEA DIRECTLY ON THEIR CUSTOMER SUPPORT FORM ON THEIR WEBSITE. THEY HAVE ALL THE PLUMBING PARTS.

 

[My90Sea]

REACH OUT TO RED SEA DIRECTLY ON THEIR CUSTOMER SUPPORT FORM ON THEIR WEBSITE. THEY HAVE ALL THE PLUMBING PARTS.

I HAVE CONTACTED THEM. I HAVE HAD 2 OTHER PEOPLE REACH OUT TO THEM AS WELL THAT ARE DISTRIBUTORS AND THEY DONT OFFER ANY PLUMBING PARTS. KINDA ODD.

 

[kinetic]

I HAVE CONTACTED THEM. I HAVE HAD 2 OTHER PEOPLE REACH OUT TO THEM AS WELL THAT ARE DISTRIBUTORS AND THEY DONT OFFER ANY PLUMBING PARTS. KINDA ODD.

I KNOW ABOUT 8 DIFFERENT PEOPLE WHO HAVE ORDERED FULL PLUMBING KITS FROM THEM NO PROBLEM. CALL THEM.

 

[My90Sea]

I KNOW ABOUT 8 DIFFERENT PEOPLE WHO HAVE ORDERED FULL PLUMBING KITS FROM THEM NO PROBLEM. CALL THEM.

OK I WILL CALL IN THE MORNING... I WILL GIVE IT ANOTHER TRY., THANKS

 

[M4rtin]

Why are you guys shouting ?

 

[reefwiser]

It must be from the noise of water splashing coming out of the pumbing.

 

[TX_Punisher]

They've, Red Sea, even
Commented on my YouTube videos. They're pretty good to work with imo.

 

[M4rtin]

Anyone here with Octo Aquatic lid ?
Care to post a picture ?

 

[gpinto81]

Anyone running Triton with a reefer 350? Im doing zeovit and have been thinking of making the change for a bit. Im just trying to figure out the sump part of triton with stock 350 sump.

I just started but going with the other methods and using an algae scrubber

 

[flowflezy]

I use 2 WAV pumps on an XL425, pretty much the same tank just a little wider.

You are correct love the WAV over the mp10. And only running 50 percent will be selling the mp10 for another WAV thanks again.

 

[CDavmd]

Hey folks,
Ordering plumbing for my 425xl - have had it for a year and a half finally getting it setup.

For those that hard plumbed with reactors, I'm not seeing unions on the reactors? I plan on using Spears gate valves.

What do you guys do to remove the reactor or do you just redo the manifold if you decide to change something?

Thanks

Hi, I'm i've been slowly setting my 425XL over the past few months. Just finishing the Manifold and reactors. I used 1/2 inch PVC and Spears gate valves and placed a 1/2 inch union at the output. It doesn't add much distance and gives me the flexibility to change things out in the future if need be.

 

[Greatreefer]

Hi, I'm i've been slowly setting my 425XL over the past few months. Just finishing the Manifold and reactors. I used 1/2 inch PVC and Spears gate valves and placed a 1/2 inch union at the output. It doesn't add much distance and gives me the flexibility to change things out in the future if need be.

CDavmd:
Could you post some picts of your plumbing so i can see what it looks like?

 

[CDavmd]

CDavmd:
Could you post some picts of your plumbing so i can see what it looks like?

I haven't mounted it yet, still piecing it together but I'll post a picture soon.

 

[Greatreefer]

Im just curious what kinds of adapers you are using to replace the non us standard plumbing?

 

[jazzmik]

Im just curious what kinds of adapers you are using to replace the non us standard plumbing?

There are a few detailed posts in this thread by @Broadfield with the adapters and sizes. He's pretty thorough so I would definitely look for those posts.


Use this as the "Search this thread only" it pulls up a bunch of the post you're going to want to read:

3/4" MPT