Did you mix the GFO with the carbon or is there a divider in there that I can't see?
6tbsp GFO(around half recommended amount) and I think 1.5c of carbon mixed. Looks like a ton of GFO but it all went to the acrylic.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Did you mix the GFO with the carbon or is there a divider in there that I can't see?
It is normally recommended to keep them separate. The GFO is harder and if it rubs against the carbon it will grind it down and release carbon dust into your tank. Your GFO should also tumble in the flow and the carbon should be tightly packed. Next time you reload it, I would run the carbon between the sponges packed tight and put the GFO above the top sponge so it can tumble. Well, as long as the plastic end strainer will keep your GFO in. I know mine does. I run my GFO reactor without sponges.6tbsp GFO(around half recommended amount) and I think 1.5c of carbon mixed. Looks like a ton of GFO but it all went to the acrylic.
It is normally recommended to keep them separate. The GFO is harder and if it rubs against the carbon it will grind it down and release carbon dust into your tank. Your GFO should also tumble in the flow and the carbon should be tightly packed. Next time you reload it, I would run the carbon between the sponges packed tight and put the GFO above the top sponge so it can tumble. Well, as long as the plastic end strainer will keep your GFO in. I know mine does. I run my GFO reactor without sponges.
It is normally recommended to keep them separate. The GFO is harder and if it rubs against the carbon it will grind it down and release carbon dust into your tank. Your GFO should also tumble in the flow and the carbon should be tightly packed. Next time you reload it, I would run the carbon between the sponges packed tight and put the GFO above the top sponge so it can tumble. Well, as long as the plastic end strainer will keep your GFO in. I know mine does. I run my GFO reactor without sponges.
Alright, I wanted to test water really quick before work... since I'm trying to get dosing dialed in and my calcium seems really high compared to alk consumption.
So lets do a bit of math. When we started our calcium was 400ppm, I have my pump set up to dose 13ml of calcium chloride 6 times a day. It dosed all six times yesterday and has dosed three times so far today for 9 total doses.
16ml x 9 = 117ml of calcium chloride suppliment which should have raised my calcium by 11ppm IF there is no consumption. My test results today, 400ppm.
For alkalinity, we have dosed 1ml 6 times a day for a total of 9 doses. Test before dosing was 8.5 and 8.6dKH, test today was 8.6 and8.7dKH. Up 0.1dKH but within error range of the test.
I'm still perplexed at how I have 13 times the calcium dose as my alk dose.... but we are a day and a half in. I'll check again in a few days.
I know, grab a beer or coffee, the token Englishman is about to ramble!
I hope your extra dose goes ok, I think you are very close to being balanced, I would suggest one tweak to your dosing, remove one kh dose from the 6 doses, something is using calcium.
Think of a tank full of jelly beans, calcium is white, kh ones are green.
Your tank is being topped up daily so your levels will be a bit off target, you will be going slowly greener, test daily even doing it your way, even corals could be using that much if they have come from a depleted tank and are just becoming healthier?! :)
Interesting! I've never heard of doing it that way before, but I think it makes sense. I'm curious to see how well you feel it works!I read where if you mix them and pack it tightly the carbon will keep the GFO from forming a brick, and being packed will keep the carbon from grinding itself. If I did them separately I would put the GFO in the bottom of the reactor under the carbon. I have an empty space there with the way I loaded it. If I put it above the only thing that would keep the GFO in the reactor is the strainer on the end of the hose.
Interesting! I've never heard of doing it that way before, but I think it makes sense. I'm curious to see how well you feel it works!
I usually run mine at 1/3 turn of the ball valve on the line until I see numbers climbing. Then I move it up a little more each time. I usually get a month out of the 1/2 cup of each. Not really sure which runs out 1st as how do you tell when rox is exhausted? I know the GFO is exhausted when flow is slowed and numbers start to climb at full. Although that could be just that it is clogged.
So... I wont name the LFS but one of them near me got this in this week. It's not for sale yet, and I've been told if it would go up for sale the price would be "4 digits plus."
This is the most amazing piece of coral I've ever seen... SPS, eat your heart out. Meet the most colorful scoly probably ever.
![]()
![]()